XR21V1412IL32-F Exar Corporation, XR21V1412IL32-F Datasheet - Page 5

• Manufacturer Part Number: XR21V1412IL32-F
• Description: IC UART FIFO USB DUAL 32QFN
• Manufacturer: Exar Corporation
• Type: USB UARTsr

Specifications of XR21V1412IL32-F

• Package / Case: 32-VFQFN Exposed Pad
• Features: *
• Number Of Channels: 2, DUART
• Fifo's: 128 Byte, 384 Byte
• Protocol: USB 2.0
• Voltage - Supply: 2.97 V ~ 3.63 V
• With Auto Flow Control: Yes
• Mounting Type: Surface Mount
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Current: 16 mA
• Operating Supply Voltage: 2.97 V to 3.63 V
• No. Of Channels: 2
• Data Rate: 12Mbps
• Uart Features: Automatic Hardware And Software Flow Control, Half-Duplex Mode, Fractional Baud Rate Generator
• Supply Voltage Range: 2.97V To 3.63V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 1016-1301 - EVAL BOARD FOR XR21V1412IL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1016-1302

REV. 1.1.0
Pin Description
USB Interface Signals
I2C Interface Signals
GPIOB2/DSRB#
GPIOB3/DTRB#
GPIOB4/CTSB#
GPIOB5/RTSB#
GPIOB1/CDB#
USBD+
USBD-
N
SDA
SCL
AME
32-QFN
P
21
20
19
18
17
30
29
25
26
IN
#
T
OD
I/O
I/O
I/O
I/O
I/O
I/O
I/O
YPE
I
UART Channel B general purpose I/O or UART Carrier-Detect input (active low).
This pin has an internal pull-up resistor which is disabled during suspend mode. If
using this GPIO as an input, an external pull-up resistor is required to minimize the
power consumption in the suspend mode.
UART Channel B general purpose I/O or UART Data-Set-Ready input (active low).
See ”Section 1.5.5, Automatic DTR/DSR Hardware Flow Control” on
page 11.
mode. If using this GPIO as an input, an external pull-up resistor is required to mini-
mize the power consumption in the suspend mode.
UART Channel B general purpose I/O or UART Data-Terminal-Ready output (active
low).
on page 11.
pend mode. If using this GPIO as an input, an external pull-up resistor is required to
minimize the power consumption in the suspend mode.
UART Channel B general purpose I/O or UART Clear-to-Send input (active low).
See ”Section 1.5.4, Automatic RTS/CTS Hardware Flow Control” on
page 10.
mode. If using this GPIO as an input, an external pull-up resistor is required to mini-
mize the power consumption in the suspend mode.
UART Channel B general purpose I/O or UART Request-to-Send output (active low).
See ”Section 1.5.4, Automatic RTS/CTS Hardware Flow Control” on
page 10.
mode. If using this GPIO as an input, an external pull-up resistor is required to mini-
mize the power consumption in the suspend mode.
USB port differential data plus. This pin has a 1.5 K Ohm internal pull-up resistor.
USB port differential data minus.
I
be used to store default configurations upon power-up including the USB Vendor ID
and Device ID. See
required.
If an EEPROM is not used, this pin can be used with the SCL pin to select the
Remote Wake-up and Power modes. An external pull-up or pull-down resistor is
required. See
I
store default configurations upon power-up including the USB Vendor ID and Device
ID. See
If an EEPROM is not used, this pin can be used with the SDA pin to select the
Remote Wake-up and Power modes. An external pull-up or pull-down resistor is
required. See
2
2
C-controller data input/output (open-drain). An optional external I
C-controller serial input clock. An optional external I
See ”Section 1.5.5, Automatic DTR/DSR Hardware Flow Control”
Table 3
This pin has an internal pull-up resistor which is disabled during suspend
This pin has an internal pull-up resistor which is disabled during suspend
This pin has an internal pull-up resistor which is disabled during suspend
Table 2
Table 2
This pin has an internal pull-up resistor which is disabled during sus-
. A pull-up resisitor (typically 4.7 to 10 KOhms) is required.
Table 3
.
.
5
. A pull-up resisitor (typically 4.7 to 10 KOhms) is
D
ESCRIPTION
2-CH FULL-SPEED USB UART
2
C EEPROM can be used to
2
XR21V1412
C EEPROM can