71M6521FE-IGT/F Maxim Integrated Products, 71M6521FE-IGT/F Datasheet - Page 82

• Manufacturer Part Number: 71M6521FE-IGT/F
• Description: IC ENERGY METER 32K FLASH 64LQFP
• Manufacturer: Maxim Integrated Products

Specifications of 71M6521FE-IGT/F

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

CE Program
The CE program is supplied as a data image that can be merged with the MPU operational code for meter
applications. Typically, the CE program covers most applications and does not need to be modified. For EQU = 0 and
EQU = 1, CE code CE21A04_2 should be used. For EQU = 2, CE code image CE21A03_2 should be used. The
description in this section applies to CE code revision CE21A03_2.
Formats
All CE words are 4 bytes. Unless specified otherwise, they are in 32-bit two’s complement (-1 = 0xFFFFFFFF).
‘Calibration’ parameters are defined in flash memory (or external EEPROM) and must be copied to CE data memory
by the MPU before enabling the CE. ‘Internal’ variables are used in internal CE calculations. ‘Input’ variables allow
the MPU to control the behavior of the CE code. ‘Output’ variables are outputs of the CE calculations. The
corresponding MPU address for the most significant byte is given by 0x1000 + 4 x CE_address and 0x1003 + 4 x
CE_address for the least significant byte.
Constants
Constants used in the CE Data Memory tables are:
The system constants IMAX and VMAX are used by the MPU to convert internal quantities (as used by the CE) to ex-
ternal, i.e. metering quantities. Their values are determined by the off-chip scaling of the voltage and current sensors
used in an actual meter. The LSB values used in this document relate digital quantities at the CE or MPU interface to
external meter input quantities. For example, if a SAG threshold of 80V peak is desired at the meter input, the digital
value that should be programmed into SAG_THR would be 80V/SAG_THR
the description of SAG_THR.
The parameters EQU, CE_E, PRE_SAMPS, and SUM_CYCLES essential to the function of the CE are stored in I/O RAM
(see I/O RAM section).
Environment
Before starting the CE using the CE_E bit, the MPU has to establish the proper environment for the CE by
implementing the following steps:
There must be thirteen 32768Hz cycles per ADC mux frame (see System Timing Diagram, Figure 16). This means
that the product of the number of cycles per frame and the number of conversions per frame must be 12 (allowing for
one settling cycle). The required configuration is FIR_LEN = 1 (three cycles per conversion) and MUX_DIV = 1 (4
conversions per mux frame).
Page: 82 of 107












F
F
IMAX is the external rms current corresponding to 250mV pk at the inputs IA and IB.
VMAX is the external rms voltage corresponding to 250mV pk at the VA and VB inputs.
N
Accumulation count time for energy measurements is PRE_SAMPS*SUM_CYCLES/F
Load the CE data into CE DRAM.
Establish the equation to be applied in EQU.
Establish the accumulation period and number of samples in PRE_SAMPS and SUM_CYCLES.
Establish the number of cycles per ADC mux frame.
Set PLS_INTERVAL[7:0] to 81.
Set FIR_LEN to 1 and MUX_DIV to 1.
S
0
ACC
is the fundamental frequency.
= 32768Hz/13 = 2520.62Hz.
, the accumulation count for energy measurements is PRE_SAMPS*SUM_CYCLES.
CE Interface Description
LSB
, where SAG_THR
71M6521DE/DH/FE Data Sheet
S
.
LSB
is the LSB value in
Rev 2