101-1284 Rabbit Semiconductor, 101-1284 Datasheet - Page 36
101-1284
Manufacturer Part Number
101-1284
Description
DEV KIT STANDARD MINI RCM5600W
Manufacturer
Rabbit Semiconductor
Series
MiniCore™r
Type
Transceiver, 802.11 b/gr
Datasheet
1.101-1285.pdf
(130 pages)
Specifications of 101-1284
Frequency
2.4GHz
Wireless Frequency
2.4 GHz
Interface Type
USB
Operating Voltage
3.3 V
Output Power
19 dBm
Antenna
U.FL Connector
Operating Temperature Range
- 30 C to + 55 C
Silicon Manufacturer
Rabbit Semiconductor
Silicon Family Name
RabbitCore
Kit Contents
Board
Features
On-board Single-Chip 802.11b/g Transceiver, Built-In Web Server
Development Tool Type
Hardware /
Rohs Compliant
Yes
For Use With/related Products
RCM5600W
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
316-1160
- Current page: 36 of 130
- Download datasheet (2Mb)
4.1.1 Memory I/O Interface
The Rabbit 5000 address lines (A0–A19) and data lines (D0–D7) are routed internally to
the onboard SRAM. I/0 write (/IOWR) and I/0 read (/IORD) are available for interfacing
to external devices.
Parallel Port A can also be used as an external I/O data bus to isolate external I/O from the
main data bus. Parallel Port B pins PB2–PB7 can also be used as an external address bus.
When using the external I/O bus for any other reason, you must add the following line at
the beginning of your program.
#define PORTA_AUX_IO
// required to enable external I/O bus
Selected pins on Parallel Ports D and E as specified in Table 2 may be used for input
capture, quadrature decoder, DMA, and pulse-width modulator purposes.
4.1.2 Other Inputs and Outputs
The status, /RESET_IN, and SMODE I/O are normally associated with the programming
port. Since the status pin is not used by the system once a program has been downloaded
and is running, the status pin can then be used as a general-purpose CMOS output. The
programming port is described in more detail in Section 4.2.2.
/RESET_IN is an external input used to reset the Rabbit 5000 microprocessor and the
RCM5600W memory. /RESET is an output from the reset circuitry that can be used to
reset other peripheral devices.
The two SMODE pins, SMODE0 and SMODE1, are tied together to +3.3 V via a pullup
resistor, and may be used as a special input when the RCM5600W is operating in the Run
Mode. The logic state of these two pins determines the startup procedure after a reset.
30
MiniCore RCM5600W
Related parts for 101-1284
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SNGLBD BL2120 FRCTNLOCK
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT APPLCTN RABBITCORE RCM4010
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT MESH NETWORK ADD-ON RCM4510W
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV FOR BL2500 COYOTE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT APPLICATION SIMPLE SENSOR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV RCM5400W US/INTERNATIONL
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DEV KIT DELUXE MINICORE RCM5600W
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT FOR BL4S100 STARTER PACKAGE
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor