TDA7210 Infineon Technologies, TDA7210 Datasheet - Page 20

• Manufacturer Part Number: TDA7210
• Description: IC RECEIVER FSK/ASK 28-TSSOP
• Manufacturer: Infineon Technologies
• Type: ASK/FSK Single Conversion Receiverr

Specifications of TDA7210

• Package / Case: 28-TSSOP
• Frequency: 810MHz ~ 870MHz, 400MHz ~ 440MHz
• Sensitivity: -110dBm
• Data Rate - Maximum: 100 kbps
• Modulation Or Protocol: ASK, FSK
• Applications: Remote Control, RKE, Security Systems
• Current - Receiving: 5.9mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Current: 7.7 mA
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: SP000524274; TDA7210; TDA7210INTR

Wireless Components
3.4.6
3.4.7
3.4.8
FSK Demodulator
To demodulate frequency shift keyed (FSK) signals a PLL circuit is used that is
contained fully on chip. The Limiter output differential signal is fed to the linear
phase detector as is the output of the 10.7 MHz center frequency VCO. The
demodulator gain is typically 200µV/kHz. The passive loop filter output that is
comprised fully on chip is fed to both the VCO and the modulation format switch
described in more detail below. This signal is representing the demodulated sig-
nal with high frequencies applied to the demodulator demodulated to logic ones
and low frequencies demodulated to logic zeroes. Please note that due to this
behaviour a sign inversion of the data occurs in case of high-side injection of
the local oscillator at receive frequencies below 840 or 420MHz, respectively.
See also .
The modulation format switch is actually a switchable amplifier with an AC gain
of 11 that is controlled by the MSEL pin (Pin 15) as shown in the following table.
This gain was chosen to facilitate detection in the subsequent circuits. The DC
gain is 1 in order not to saturate the subsequent Data Filter wih the DC offset
produced by the demodulator in case of large frequency offsets of the IF signal.
The resulting frequency characteristic and details on the principle of operation
of the switch are described in Section 4.6.
The demodulator circuit is switched off in case of reception of ASK signals.
Data Filter
The data filter comprises an OP-Amp with a bandwidth of 100kHz used as a
voltage follower and two 100kΩ on-chip resistors. Along with two external
capacitors a 2nd order Sallen-Key low pass filter is formed. The selection of the
capacitor values is described in Section 4.2.
Data Slicer
The data slicer is a fast comparator with a bandwidth of 100 kHz. This allows
for a maximum receive data rate of up to 100kBaud. The maximum achievable
data rate also depends on the IF Filter bandwidth and the local oscillator toler-
ance values. Both inputs are accessible. The output delivers a digital data sig-
nal (CMOS-like levels) for sbsequent circuits. The self-adjusting threshold on
pin 20 its generated by RC-term or peak detector depending on the baseband
coding scheme. The data slicer threshold generation alternatives are described
in more detail in Section 4.5.
Table 3-4 MSEL Pin Operating States
MSEL
Open
Shorted to ground
3 - 12
Modulation Format
Data Sheet, December 2008
Functional Description
ASK
FSK
TDA7210