ATMEGA2560R231-CU Atmel, ATMEGA2560R231-CU Datasheet - Page 116

• Manufacturer Part Number: ATMEGA2560R231-CU
• Description: BUNDLE ATMEGA2560/RF231 PBGA
• Manufacturer: Atmel

Specifications of ATMEGA2560R231-CU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
• Data Interface: PCB, Surface Mount
• Memory Size: 256kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 100-CBGA and 32-QFN
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 256 KB
• Data Ram Size: 8 KB
• Development Tools By Supplier: ATAVRRZ541, ATAVRRAVEN, ATAVRRZRAVEN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Power - Output: -
• Operating Temperature: -
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

14.2.6
14.2.7
14.2.8
2549M–AVR–09/10
PCIFR – Pin Change Interrupt Flag Register
PCMSK2 – Pin Change Mask Register 2
PCMSK1 – Pin Change Mask Register 1
• Bit 0 – PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 0 is enabled. Any change on any enabled PCINT7:0 pin will cause an interrupt.
The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI0 Interrupt
Vector. PCINT7:0 pins are enabled individually by the PCMSK0 Register.
• Bit 2 – PCIF2: Pin Change Interrupt Flag 1
When a logic change on any PCINT23:16 pin triggers an interrupt request, PCIF2 becomes set
(one). If the I-bit in SREG and the PCIE2 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 1 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT15:8 pin triggers an interrupt request, PCIF1 becomes set
(one). If the I-bit in SREG and the PCIE1 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 0 – PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7:0 pin triggers an interrupt request, PCIF0 becomes set
(one). If the I-bit in SREG and the PCIE0 bit in PCICR are set (one), the MCU will jump to the
corresponding Interrupt Vector. The flag is cleared when the interrupt routine is executed. Alter-
natively, the flag can be cleared by writing a logical one to it.
• Bit 7:0 – PCINT23:16: Pin Change Enable Mask 23:16
Each PCINT23:16-bit selects whether pin change interrupt is enabled on the corresponding I/O
pin. If PCINT23:16 is set and the PCIE2 bit in PCICR is set, pin change interrupt is enabled on
the corresponding I/O pin. If PCINT23:16 is cleared, pin change interrupt on the corresponding
I/O pin is disabled.
Bit
0x1B (0x3B)
Read/Write
Initial Value
Bit
(0x6D)
Read/Write
Initial Value
Bit
(0x6C)
Read/Write
Initial Value
PCINT15
PCINT23
R/W
R/W
7
0
7
0
R
7
–
0
PCINT22
PCINT14
R/W
R/W
6
0
6
0
R
6
–
0
PCINT21
PCINT13
ATmega640/1280/1281/2560/2561
R/W
R/W
0
5
0
5
R
5
–
0
PCINT20
PCINT12
R/W
R/W
4
0
4
0
R
4
–
0
PCINT19
PCINT11
R/W
R/W
3
0
3
0
R
3
–
0
PCINT18
PCINT10
PCIF2
R/W
R/W
R/W
2
0
2
0
2
0
PCINT17
PCINT9
PCIF1
R/W
R/W
R/W
1
0
1
0
1
0
PCINT16
PCINT8
PCIF0
R/W
R/W
R/W
0
0
0
0
0
0
PCMSK2
PCMSK1
PCIFR
116