ATMEGA2560R231-CU Atmel, ATMEGA2560R231-CU Datasheet - Page 35

• Manufacturer Part Number: ATMEGA2560R231-CU
• Description: BUNDLE ATMEGA2560/RF231 PBGA
• Manufacturer: Atmel

Specifications of ATMEGA2560R231-CU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
• Data Interface: PCB, Surface Mount
• Memory Size: 256kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 100-CBGA and 32-QFN
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 256 KB
• Data Ram Size: 8 KB
• Development Tools By Supplier: ATAVRRZ541, ATAVRRAVEN, ATAVRRZRAVEN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Power - Output: -
• Operating Temperature: -
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

8.2
8.2.1
8.2.1.1
8.2.1.2
8.2.1.3
2549M–AVR–09/10
Register Description
EEPROM registers
EEARH and EEARL – The EEPROM Address Register
EEDR – The EEPROM Data Register
EECR – The EEPROM Control Register
• Bits 15:12 – Res: Reserved Bits
These bits are reserved bits and will always read as zero.
• Bits 11:0 – EEAR8:0: EEPROM Address
The EEPROM Address Registers – EEARH and EEARL specify the EEPROM address in the 4
Kbytes EEPROM space. The EEPROM data bytes are addressed linearly between 0 and 4096.
The initial value of EEAR is undefined. A proper value must be written before the EEPROM may
be accessed.
• Bits 7:0 – EEDR7:0: EEPROM Data
For the EEPROM write operation, the EEDR Register contains the data to be written to the
EEPROM in the address given by the EEAR Register. For the EEPROM read operation, the
EEDR contains the data read out from the EEPROM at the address given by EEAR.
• Bits 7:6 – Res: Reserved Bits
These bits are reserved bits and will always read as zero.
• Bits 5, 4 – EEPM1 and EEPM0: EEPROM Programming Mode Bits
The EEPROM Programming mode bit setting defines which programming action that will be trig-
gered when writing EEPE. It is possible to program data in one atomic operation (erase the old
value and program the new value) or to split the Erase and Write operations in two different
operations. The Programming times for the different modes are shown in
While EEPE is set, any write to EEPMn will be ignored. During reset, the EEPMn bits will be
reset to 0b00 unless the EEPROM is busy programming.
Bit
0x22 (0x42)
0x21 (0x41)
Read/Write
Initial Value
Bit
0x20 (0x40)
Read/Write
Initial Value
Bit
0x1F (0x3F)
Read/Write
Initial Value
EEAR7
R/W
MSB
R/W
15
R
–
7
0
X
R
7
–
0
7
0
EEAR6
R/W
R/W
14
R
X
–
6
0
R
6
–
0
6
0
ATmega640/1280/1281/2560/2561
EEAR5
EEPM1
R/W
R/W
R/W
13
R
X
–
5
0
X
5
5
0
EEAR4
EEPM0
R/W
R/W
R/W
12
R
–
4
0
X
X
4
4
0
EEAR11
EEAR3
EERIE
R/W
R/W
R/W
R/W
11
X
X
3
3
0
3
0
EEAR10
EEMPE
EEAR2
R/W
R/W
R/W
R/W
10
2
0
X
X
2
0
2
EEAR9
EEAR1
EEPE
R/W
R/W
R/W
R/W
1
0
1
X
X
X
9
1
Table 8-1 on page
EEAR8
EEAR0
EERE
LSB
R/W
R/W
R/W
R/W
X
X
0
0
0
0
8
0
EEARH
EEARL
EEDR
EECR
36.
35