ATMEGA2560R231-CU Atmel, ATMEGA2560R231-CU Datasheet - Page 361

• Manufacturer Part Number: ATMEGA2560R231-CU
• Description: BUNDLE ATMEGA2560/RF231 PBGA
• Manufacturer: Atmel

Specifications of ATMEGA2560R231-CU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
• Data Interface: PCB, Surface Mount
• Memory Size: 256kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 100-CBGA and 32-QFN
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 256 KB
• Data Ram Size: 8 KB
• Development Tools By Supplier: ATAVRRZ541, ATAVRRAVEN, ATAVRRZRAVEN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Power - Output: -
• Operating Temperature: -
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

Table 29-18. JTAG Programming Instruction (Continued)
Notes:
2549M–AVR–09/10
Instruction
8d. Read Fuse Low Byte
8e. Read Lock Bits
8f. Read Fuses and Lock Bits
9a. Enter Signature Byte Read
9b. Load Address Byte
9c. Read Signature Byte
10a. Enter Calibration Byte Read
10b. Load Address Byte
10c. Read Calibration Byte
11a. Load No Operation Command
1. This command sequence is not required if the seven MSB are correctly set by the previous command sequence (which is
2. Repeat until o = “1”.
3. Set bits to “0” to program the corresponding Fuse, “1” to unprogram the Fuse.
4. Set bits to “0” to program the corresponding Lock bit, “1” to leave the Lock bit unchanged.
5. “0” = programmed, “1” = unprogrammed.
6. The bit mapping for Fuses Extended byte is listed in
7. The bit mapping for Fuses High byte is listed in
8. The bit mapping for Fuses Low byte is listed in
9. The bit mapping for Lock bits byte is listed in
10. Address bits exceeding PCMSB and EEAMSB
11. All TDI and TDO sequences are represented by binary digits (0b...).
normally the case).
Set (Continued)
o = data out, i = data in, x = don’t care
(9)
(8)
a = address high bits, b = address low bits, c = address extended bits, H = 0 - Low byte, 1 - High Byte,
TDI Sequence
0110010_00000000
0110011_00000000
0110110_00000000
0110111_00000000
0111010_00000000
0111110_00000000
0110010_00000000
0110110_00000000
0110111_00000000
0000011_bbbbbbbb
0110010_00000000
0110011_00000000
0000011_bbbbbbbb
0110110_00000000
0110111_00000000
0100011_00000000
0110011_00000000
0100011_00001000
0100011_00001000
Table 29-1 on page
Table 29-5 on page
(Table 29-7 on page 338
Table 29-4 on page
Table 29-3 on page
ATmega640/1280/1281/2560/2561
335.
337.
337.
TDO Sequence
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxoooooo
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_oooooooo
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
xxxxxxx_xxxxxxxx
and
336.
Table 29-8 on page
338) are don’t care.
Notes
(5)
(5)
Fuse Ext. byte
Fuse High byte
Fuse Low byte
Lock bits
361