CTE701 3M, CTE701 Datasheet

WORKSTATION MONITOR CHECKER

CTE701

Manufacturer Part Number
CTE701
Description
WORKSTATION MONITOR CHECKER
Manufacturer
3M
Series
ScanEM® Probesr
Type
Monitorr
Datasheet
1.CTE701.pdf (4 pages)

Specifications of CTE701

Description/function
Workstation Monitor Checkers
For Use With/related Products
Workstation, Wrist Straps
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Features
-
Power Supply Type
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
51111161982
80000919490
SCP265
XA004143203
© 2006 Credence Technologies, Inc.
Ground Masteris registered trademark
of Credence Technologies, Inc.
Patent Pending. Made in U.S.A.
Procedure
Credence Technologies, Inc. warrants Worskstation Monitor Checker to be free from defects in materials and
workmanship under normal use and service for a period of one (1) year from date of purchase directly from
Credence Technologies, Inc., or from its authorized distributors. This warranty extends only to the original
purchaser. This warranty shall not apply to any product or part of it which has been subjected to misuse,
neglect, accident or abnormal conditions of operation. Except to the extent precluded by applicable state
law, Credence Technologies will have no liability for any consequential, incidental, or special damages.
In the event of failure of a product covered by this warranty, Credence Technologies, Inc. will repair a
product returned to authorized distributor or, only if it was purchased directly from Credence Technologies,
Inc., to the manufacturer; provided the warrantorís examination discloses to the company’s satisfaction
that the product was defective and is qualified for to a warranty claim. Credence Technologies may, at its
option, replace the product or its components with new or factory-refurbished parts or as whole in lieu of
repair. With regard to a product returned within one year of its purchase, said repair or replacement will
be made without charge. If the failure has been caused by misuse, neglect, accident or abnormal
conditions of operation, repairs will be billed at a nominal cost. Warranty does not cover transportation
costs.
your monitor.
indicate good connection.
“High” button.
each polarity -- positive and negative. If you ordered Checker for WS Aware
with a single terminal for both operators (model CTC061-D), please see
special addendum. When Body Voltage Low button is depressed, no Body
Voltage indication should be present in the monitor.
Connect 3.5mm test cable to both the Checker and to Operator jack of
Depress and keep pressed the “Wriststrap” button. Your monitor should
While keeping Pass button, depress and keep pressed Body Voltage
Your monitor should provide indication of excessive body voltage in
Follow instructions in Basics
Limited Warranty
Basics
Basics
Basics
Basics section
Credence Technologies, Inc.
3601-A Caldwell Dr.
Soquel, CA 95073 U.S.A.
Tel. 831-459-7488 FAX 831-427-3513
www.credencetech.com
Workstation
Monitor
Checker
Model CTE701A
Credence Technologies, Inc.
User’s Guide

CTE701 Summary of contents

Page 1

... Credence Technologies, Inc. 3601-A Caldwell Dr. © 2006 Credence Technologies, Inc. Soquel, CA 95073 U.S.A. Ground Masteris registered trademark Tel. 831-459-7488 FAX 831-427-3513 of Credence Technologies, Inc. Patent Pending. Made in U.S.A. www.credencetech.com Workstation Monitor Checker Model CTE701A User’s Guide Credence Technologies, Inc. ...

Page 2

... Workstation Monitor Checker model CTE701 is designed to verify proper opera- tion of your dual wriststrap monitors, workstation monitors and ground monitors. Checker simulates proper resistances and signals so that you can see whether the response of your monitors complies with your specification ...

Page 3

EMI “High” button. In Ground Master you should see green light indicating good ground connection and blinking red light indicating presence of EMI Aware the ground light should be pulsed yellow light or continuous yellow (older models). ...

Page 4

Basics For all tests make sure that: Monitor under test itself is properly grounded and is operational. Disconnect all wires from the monitor under test that go to the monitored grounds. Leave ground connection of the monitor itself con- nected ...