025-0767-001 ITT Cannon, 025-0767-001 Datasheet - Page 112

• Manufacturer Part Number: 025-0767-001
• Description: RP CONDUCTIVE D/C 34 SHELL
• Manufacturer: ITT Cannon

Specifications of 025-0767-001

• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: I025-0767-001

ITT Cannon recommends resistance soldering for all
solder contacts, particularly for RF cable where
excessive heat will damage the dielectric. Wires
should be pre-tinned. Shells, bushings, endbells and
junction shells Jwhere applicable) must be slipped
over wire bundles before soldering or crimping is
started. The mechanical steps in wiring coaxials are
described below.
Straight
R Coax
90 angle
R Coax
Single Gang - DPD/DPDMA
The DPD/DPDMA can be engaged by means of a
No. 10-32 steel jack screw and clinch nut. This
coupling device is designed to fasten connectors
securely when they are used in other than standard
rack/ panel applications. The jack screws and clinch
nuts are mounted on the shell flanges at the factory.
They may be called out on either -33 or -34 shelis,
although it is preferred to have jack screws on the
-33 shell and the clinch nuts on the -34 shell. The
device can be ordered on both DPD and DPDMA.
Engaging Devices
The suffix "N" or "S" is placed immediately after the mounting
hole variation; i.e., - 1AN, -1AS, etc.
Engaging Device
How to Order
DPD-**-34*-1* N
Two Gang - DPD2/DPD2MA
The DPD2 is engaged by means of a variety of
screw mechanisms. Engaging devices are inter-
changeable (within the thread group) with male or
female mounting on either 33 or 34 shells. The
accompanying tabulation lists the available engag-
ing devices, male opposite female, with which they
mate.
How to Order
Stripping Instructions
DPD/DPDMA
Coax Type
Cable Size
RG-7/U
RG-59/U
RG-62/U
RG-7/U
RG-58/U
RG-59/U
RG-62/U
N = Clinch Nut
S = Jack Screw
.171 (4.34)
.171 (4.34)
.171 (4.34)
.218 (5.54)
.218 (5.54)
.218 (5.54)
.218 (5.54)
A
DPD2
.421 (10.69)
.546 (13.87)
.543 (13.87)
.312 (7.92)
.531 (13.49)
.531 (13.49)
.531 (13.49)
Trim
B
-72C2
DPD-**-33*-1* S
.515 (13.08)
.671 (17.04)
.671 (17.04)
.437 (11.10)
.593 (15.06)
.593 (15.06)
.593 (15.06)
-34PCM
C
1. Cut cable even. Trim to dimensions shown on
tabulation. Care should be taken not to injure
the conductor or dielectric.
3. Remove solder pot cover. Insert cable and solder
conductor to contact. If a straight contact is
used, the dielectric should but against contact
solder pot.
R Coaxial (Straight and 90 )
Number
M
MA
CM
CMRA
DM
DM-1
DM-2
DM-3
DM-7
Part
#10-32
clinch nut
on horizontal
center line
MALE ENGAGING DEVICES
COVER
BRAID
Used On
DPD2MA
DPD2
-34
Shell
112
B
C
A
DIELECTRIC
CONDUCTOR
#10-32 steel jack screw (on horizontal center line)
F
2. Comb braid, tin conductor and remove flux. If a
90 contact is used, bend conductor 90˚ after
tinning.
4. Replace solder pot cover and solder braid to
ferrule.
Specifications and dimensions subject to change
FEMALE ENGAGING DEVICES
Straight
-33
Shell
CF
Dimensions shown in inch (mm)
www.ittcannon.com
1/4 hex with
screwdriver
slot &
safety wire
hole
90
DF