025-0767-001 ITT Cannon, 025-0767-001 Datasheet - Page 93

• Manufacturer Part Number: 025-0767-001
• Description: RP CONDUCTIVE D/C 34 SHELL
• Manufacturer: ITT Cannon

Specifications of 025-0767-001

• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: I025-0767-001

Coaxial Contact/Assembly
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
www.ittcannon.com
MIL-C-83733
STEP 1.
Slide outer ring over cable as shown (Figure 1).
STEP 2.
Strip cable as shown (Figure 1).
STEP 3.
Install body insert, insulatro bed, and contact on cable as shown
(Figure 2.)
STEP 4.
With body insert, insulator bead, and contact firmly in place, crimp the
contact with tool M22520/2-01 (setting number 3) and loacator
M22520/2-30 (Figure 2). Caution: The assembled componenets must
be tightly in place after crimping.
*These contacts are used in the F59C7 layout.
STEP 1.
Slide heat-shrink sleeve and outer ring over cable as shown.
STEP 2.
Strip cable as shown (Figure 1). Caution: Do not nick shield wires.
STEP 3.
Install body insert, insulator bead, and contact on cable as shown.
STEP 4.
*These contacts are used in the G59C7 layout.
249-5500-010 Socket*
249-5500-011 PIN*
249-5500-012 Socket*
249-5500-013 PIN*
With body insert, insulator bead, and contact firmly in place, crimp the
contact with tool M22520/2-01, using setting number 3 and loacator
M22520/2-30 (Figure 2). Caution: The assembled componenets must
be tightly in place after crimping.
HEAT SHRINK
SLEEVE
RING, OUTER
COAXIAL CABLE
RG-188/U
COAXIAL CABLE
RG-180/U OR RG-195/U
RING, OUTER
BODY INSERT
BODY INSERT
INSULATOR, BEAD
CONTACT, SOCKET
INSULATOR, BEAD
CONTACT, SOCKET
CONTACT, PIN
CONTACT, PIN
STEP 5.
Slide body assembly over componenets and under shield until firmly
bottomed in place. Locate outer ring over shield and against body as
shown (Figure 3).
STEP 6.
With cable and body assembly securely held together, hex crimp the
outer ring with tool CCT-C9 (Figure 3). Important: For optimum hex
crimp, firmly bottom the outer ring against the shoulder of the hex die
before compressing the handles.
STEP 5.
Slide body assembly over componenets and under shield until firmly
bottomed in place. Locate outer ring over shield and against body as
shown (Figure 3).
STEP 6.
With cable and body assembly securely held together, hex crimp the
outer ring with tool CCT-C9 (Figure 3). Important: For optimum hex
crimp, firmly bottom the outer ring against the shoulder of the hex die
before compressing the handles.
STEP 7.
of 149 C to 327 C (300 F to 621 F) (Figure 3).
The final step is to shrink the heat sleeve in place with a hot air source
BODY ASSEMBLY
BODY ASSEMBLY
93
BODY ASSEMBLY
BODY ASSEMBLY
NOTES:
NOTES:
1. These assembly instructions apply to 249-5500-010,
2. The following assembly tools are required:
1. These assembly instructions apply to 249-5500-010,
2. The following assembly tools are required:
and 249-5500-011.
and 249-5500-011.
a) CCT-C9 hex crimp tool
b) MS3198-Q W/L-3198-C1 contact crimp tool and
c) 149 C(300 F) hot air gun (recommended): Regal
heat Gun No. 9A)
d) Blades, scissors, and picks
a) CCT-C9 hex crimp tool
b) M22520/2-01 contact crimp tool and locator
c) 149 C(300 F) hot air gun (recommended): Regal
heat Gun No. 9A)
d) Blades, scissors, and picks
BODY INSERT
locator
INSULATOR, BEAD
BODY INSERT
3/8 + _ 1/64
(9.52 + _ 0.40)
HEX CRIMP
INSULATOR, BEAD
5/16 + _ 1/64
(7.94 + _ 0.40)
HEX CRIMP
SLEEVE,
HEAT SHRINK
8 INDENT CRIMP
8 INDENT CRIMP
DPK
RING, OUTER
RING, OUTER
CENTER CONDUCTOR
MUST BE VISIBLE
IN INSEPECTION HOLE
CENTER CONDUCTOR
MUST BE VISIBLE
IN INSEPECTION HOLE
CONTACT, PIN
OR SOCKET
CONTACT, PIN
OR SOCKET
13/64 + _ 1/64
(5.16 + _ 0.40)
BODY ASSEMBLY
13/64 + _ 1/64
(5.16 + _ 0.40)
BODY ASSEMBLY
3/16 + _ 1/64
(4.76 + _ 0.40)
1/8 + _ 1/64
(3.18 + _ 0.40)