MC9S08SH8CWJR Freescale Semiconductor, MC9S08SH8CWJR Datasheet - Page 170

• Manufacturer Part Number: MC9S08SH8CWJR
• Description: IC MCU 8BIT 8K FLASH 20WSOIC
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH8CWJR

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (0.300", 7.50mm Width)
• Processor Series: S08SH
• Core: HCS08
• Data Bus Width: 8 bit
• Interface Type: SPI, SCI, RS-232
• Maximum Clock Frequency: 5 MHz, 40 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08SG32, DEMO9S08SG32AUTO, DEMO9S08SG8, DEMO9S08SG8AUTO, DEMO9S08SH32, DEMO9S08SH8
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 11 Inter-Integrated Circuit (S08IICV2)
11.3.3
170
Reset
IICEN
TXAK
RSTA
Field
IICIE
MST
TX
7
6
5
4
3
2
W
R
IICEN
IIC Control Register (IICC1)
IIC Enable. The IICEN bit determines whether the IIC module is enabled.
0 IIC is not enabled
1 IIC is enabled
IIC Interrupt Enable. The IICIE bit determines whether an IIC interrupt is requested.
0 IIC interrupt request not enabled
1 IIC interrupt request enabled
Master Mode Select. The MST bit changes from a 0 to a 1 when a start signal is generated on the bus and
master mode is selected. When this bit changes from a 1 to a 0 a stop signal is generated and the mode of
operation changes from master to slave.
0 Slave mode
1 Master mode
Transmit Mode Select. The TX bit selects the direction of master and slave transfers. In master mode, this bit
should be set according to the type of transfer required. Therefore, for address cycles, this bit is always high.
When addressed as a slave, this bit should be set by software according to the SRW bit in the status register.
0 Receive
1 Transmit
Transmit Acknowledge Enable. This bit specifies the value driven onto the SDA during data acknowledge
cycles for master and slave receivers.
0 An acknowledge signal is sent out to the bus after receiving one data byte
1 No acknowledge signal response is sent
Repeat start. Writing a 1 to this bit generates a repeated start condition provided it is the current master. This
bit is always read as cleared. Attempting a repeat at the wrong time results in loss of arbitration.
0
7
= Unimplemented or Reserved
IICIE
0
6
Figure 11-5. IIC Control Register (IICC1)
MC9S08SH8 MCU Series Data Sheet, Rev. 3
Table 11-6. IICC1 Field Descriptions
MST
0
5
TX
0
4
Description
TXAK
3
0
RSTA
0
0
2
Freescale Semiconductor
0
0
1
0
0
0