AFBR-57R6AEZ Avago Technologies US Inc., AFBR-57R6AEZ Datasheet - Page 8

• Manufacturer Part Number: AFBR-57R6AEZ
• Description: Fiber Optic Transmitters, Receivers, Transceivers Transceiver
• Manufacturer: Avago Technologies US Inc.
• Series: -r

Specifications of AFBR-57R6AEZ

• Product: Transceiver
• Data Rate: 4.25 GBd, 2.125 GBd, 1.0625 GBd, 1.25 GBd
• Wavelength: 860 nm (Max)
• Maximum Rise Time: 0.09 ns/0.15 ns
• Maximum Fall Time: 0.09 ns/0.15 ns
• Pulse Width Distortion: 0.06 ns (Max)/0.062 ns (Max)
• Maximum Output Current: 300 mA
• Operating Supply Voltage: 2.97 V to 3.63 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 10 C
• Package / Case: SFP
• Mounting Type: SFP
• Voltage - Supply: 2.97 V ~ 3.63 V
• Connector Type: LC Duplex
• Applications: Ethernet
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Multimode Fiber
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

8
Table 3. Absolute Maximum Ratings
Parameter
Storage Temperature
Case Operating Temperature
Relative Humidity
Supply Voltage
Low Speed Input Voltage
Notes:
1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short
2. Between Absolute Maximum Ratings and the Recommended Operating Conditions functional performance is not intended, device reliability is
3. The module supply voltages, V
Table 4. Recommended Operating Conditions
Parameter
Case Operating Temperature
Supply Voltage
Data Rate
Notes:
1. The Ambient Operating Temperature limitations are based on the Case Operating Temperature limitations and are subject to the host system
2. Recommended Operating Conditions are those values for which functional performance and device reliability is implied.
Table 5. Transceiver Electrical Characteristics
(T
Parameter
AC Electrical Characteristics
Power Supply Noise Rejection (peak-peak)
DC Electrical Characteristics
Module Supply Current
Power Dissipation
Low Speed Outputs:
Low Speed Inputs:
Notes:
1. Filter per SFP specification is required on host board to remove 10 Hz to 2 MHz content.
2. Pulled up externally with a 4.7 k – 10 kΩ resistor on the host board to 3.3 V.
3. Mod-Def1, Mod-Def2 and RATE_SELECT must be pulled up externally with a 4.7 k – 10 kΩ resistor on the host board to 3.3 V.
C
Transmit Fault (TX_FAULT), Loss of Signal
(RX_LOS), MOD-DEF 2
Transmit Disable (TX_DIS), MOD-DEF 1,
MOD-DEF2, Rate Select (RATE_SELECT)
period of time. See Reliability Data Sheet for specific reliability performance.
not implied, and damage to the device may occur over an extended period of time.
thermal design.
= -10°C to 85°C, VccT, VccR = 3.3 V ± 10%)
CC
T and V
CC
R must not differ by more than 0.5 V or damage to the device may occur.
Symbol
T
T
RH
Vcc
V
Symbol
T
Vcc
S
C
IN
C
T, R
T, R
Symbol
PSNR
I
P
V
V
V
V
CC
DISS
OH
OL
IH
IL
Minimum
-40
-40
5
-0.5
-0.5
Minimum
-10
2.97
1.0625
Minimum
100
2.0
2.0
0
Maximum
100
100
95
3.8
Vcc + 0.5
Maximum
85
3.63
4.25
Typical
Maximum
210
765
VccT, R+0.3
0.8
Vcc
0.8
Unit
C
C
%
V
V
Unit
°C
V
Gb/s
Unit
mV
mA
mW
V
V
V
V
Notes
Note 1, 2
Note 1, 2
Note 1
Note 1, 2, 3
Note 1
Notes
Note 1, 2
Note 2
Note 2
Notes
Note 1
Note 2
Note 3