PVZ2A103C04R00 Murata, PVZ2A103C04R00 Datasheet - Page 69

• Manufacturer Part Number: PVZ2A103C04R00
• Description: Trimmer Resistors - SMD 10Kohms Open 2mm Carbon
• Manufacturer: Murata
• Type: Trimming Potentiometerr

Specifications of PVZ2A103C04R00

• Resistance: 10 KOhms
• Power Rating: 0.1 Watt (1/10 Watt)
• Operating Temperature Range: - 25 C to + 85 C
• Element Type: Carbon
• Dimensions: 2.1 mm W x 2.7 mm L x 0.8 mm H
• Product: Single-Turn Trimmer Potentiometers
• Termination Style: Solder Pad
• Tolerance: 30 %
• Number Of Turns: 1
• Taper: Linear
• Temperature Coefficient: +/- 500 PPM / C
• Product Type: Single Turn
• Adjustment: Top Crossed
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu), Eutectic solder (63Sn/37Pb)
1. Use suitable screwdrivers that fit comfortably in
2. Don't apply more than 9.8N (Ref.; 1kgf) of twist
1. Please make sure that your product has been
2. Murata cannot guarantee trimmer potentiometer
68
PV12/PV37/PV23/PV22/PV36 Series Notice
Temperature of Soldering Iron Tip
Soldering Profile
Notice (Handling)
driver slot. We recommend the screwdrivers below.
* Recommended screwdriver for manual adjustment
We can supply the screwdrivers above.
If you place order, please specify the Murata P/N.
and stress after mounting onto PCB to prevent
contact intermittence. If excessive force is
applied, the trimmer potentiometer may not
function.
Notice (Other)
evaluated and confirmed against your
specifications when our product is mounted to your
product.
integrity when used under conditions other than
those specified in this document.
Flow Soldering Profile
Soldering Iron
ENGINEER INC.: DA-40
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
(Murata P/N: KMDR180)
T1
350 10
C
Pre-heating
t1
T3
T2
Heating
t2
Time (s)
Soldering Time
Limit Profile
Standard Profile
3 max.
sec.
Standard Condition
3. When adjusting with an adjustment tool, the applied
4. When using a lock paint to fix slot position,
force to the adjustment screw should not exceed
4.9N (Ref.; 500gf). If excessive force is applied,
the trimmer potentiometer may not function due to
damage.
please use adhesive resin without chlorine or
sulfur (Three-bond "1401 series") and evaluate
performance by your products. Lock paint may
cause corroison or electrical contact problems.
Temp. (T1)
Temp. (T1)
Soldering Iron Power Output
150
150
C
C
Pre-heating
Pre-heating
30 max.
W
60 to 120
60 to 120
Time (t1)
Time (t1)
sec.
sec.
Standard Profile
Temp. (T2)
Limit Profile
Temp. (T3)
250
260
C
C
Heating
Heating
Cycle of Soldering Iron
Time (t2)
Time (t2)
5 max.
3 max.
sec.
sec.
Time
1
Cycle of Flow
Cycle of Flow
Time
Time
1
1
R50E.pdf
05.9.9