PVZ2A103C04R00 Murata, PVZ2A103C04R00 Datasheet - Page 75
![Trimmer Resistors - SMD 10Kohms Open 2mm Carbon](/photos/16/33/163349/poz2anpt_sml.jpg)
PVZ2A103C04R00
Manufacturer Part Number
PVZ2A103C04R00
Description
Trimmer Resistors - SMD 10Kohms Open 2mm Carbon
Manufacturer
Murata
Type
Trimming Potentiometerr
Datasheets
1.PVG5A101C01R00.pdf
(89 pages)
2.PVM4A201D01R00.pdf
(55 pages)
3.PVG5A201C01R00.pdf
(90 pages)
Specifications of PVZ2A103C04R00
Resistance
10 KOhms
Power Rating
0.1 Watt (1/10 Watt)
Operating Temperature Range
- 25 C to + 85 C
Element Type
Carbon
Dimensions
2.1 mm W x 2.7 mm L x 0.8 mm H
Product
Single-Turn Trimmer Potentiometers
Termination Style
Solder Pad
Tolerance
30 %
Number Of Turns
1
Taper
Linear
Temperature Coefficient
+/- 500 PPM / C
Product Type
Single Turn
Adjustment
Top Crossed
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PVZ2A103C04R00
Manufacturer:
MURATA
Quantity:
240 000
Part Number:
PVZ2A103C04R00
Manufacturer:
MURATA/村田
Quantity:
20 000
10
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. Do not use the rotary position sensor under the
1. When installing sensor, tighten the nut at the
2. When coupling to the shaft of sensor, handle within
3. Don't wire the sensor while the power supply is ON.
1. Uncontrolled mechanical force except usual rotation
1. Input voltage
2. Influence of magnetic field
74
SV21 Series Notice
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
following environmental conditions. If you use
the rotary position sensor in an environment other
these listed below, please consult with Murata
factory representative prior to using.
Notice (Soldering and Mounting)
torque levels less than 1.0N.m (10kgf.cm as
reference).
The exceeded force might damage the screw thread
of sensor.
max. value of shaft force.
Be careful during wiring.
Notice (Handling)
on the shaft of product, may cause big change of
electrical characteristic, big increase of
rotational torque or mechanical damage of product.
Therefore, please pay your attention on the
following points for your design.
Please design your coupler by holding shaft bush
to avoid exceeded radial or thrust shaft force of
sensor.
Notice (Other)
Please design the input voltage value of less
deteriorated with age and smaller ripple because of
direct influence for output voltage.
Though the protection circuit of 8.5V is installed,
the exceeded input voltage might damage inner
circuit of sensor.
Don't place another magnetic materials or magnetic
generator. These might happen malfunction of your
set due to changing the output voltage of sensor.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
4. Please design the cable wire to avoid the influence
5. Please use the recommended connector which is
6. Can not be cleaned by any solvents due to the open
2. The magnetic is installed inside of sensor.
(1) Corrosive gasses atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(1) If sensor closes magnetic storage (magnetic tape,
(2) Don't close sensor to patient who is wearing
of the power line or high voltage line.
"ZHR-3 series / J.S.T. made".
When using other connector, the contact problem
might happen or the connector might be damaged.
construction.
Please pay your attention as below.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Water, Oil, Medical liquid, Organic
solvent, etc.)
floppy disc drive etc.), the magnetic memory
might be damaged.
electrical medical equipmets. The equipment might
malfunction due to magnetic influence of sensor.
R50E.pdf
05.9.9
10