ISP1507BBS ST-Ericsson Inc, ISP1507BBS Datasheet - Page 19

• Manufacturer Part Number: ISP1507BBS
• Description: IC, TRANSCEIVER, USB OTG, 32HVQFN
• Manufacturer: ST-Ericsson Inc

Specifications of ISP1507BBS

• Usb Type: USB Transceiver
• Usb Version: 2.0
• Data Rate: 12Mbps
• No. Of Ports: 1
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: QFN
• No. Of Pins: 32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 7.
Table 8.
CD00222689
Product data sheet
Signal
TX_ENABLE
DAT
SE0
INT
Reserved
Signaling mode
General settings
3-state drivers
Power-up or
V
Host settings
Host chirp
Host high-speed
Host full-speed
Host high-speed or
full-speed suspend
Host high-speed or
full-speed resume
Host low-speed
BUS
< V
B_SESS_END
Signal mapping for 3-pin serial mode
Operating states and their corresponding resistor settings
8.2 USB and OTG state transitions
Maps to
DATA0
DATA1
DATA2
DATA3
DATA[7:4]
Register settings
XCVR
SELECT
[1:0]
XXb
01b
00b
00b
X1b
01b
01b
10b
A Hi-Speed USB peripheral, host or OTG device handles more than one electrical state as
defined in Universal Serial Bus Specification Rev. 2.0 and On-The-Go Supplement to the
USB 2.0 Specification Rev. 1.3. The ISP1507 accommodates various states through
register bit settings of XCVRSELECT[1:0], TERMSELECT, OPMODE[1:0],
DP_PULLDOWN and DM_PULLDOWN.
Table 8
resistor settings as also given in
It is up to the link to set the desired register settings.
•
•
•
•
RPU_DP_EN enables the 1.5 kΩ pull-up resistor on DP
RPD_DP_EN enables the 15 kΩ pull-down resistor on DP
RPD_DM_EN enables the 15 kΩ pull-down resistor on DM
HSTERM_EN enables the 45 Ω termination resistors on DP and DM
summarizes operating states. The values of register settings in
TERM
SELECT
Xb
0b
0b
0b
1b
1b
1b
1b
O
O
Direction
I
I/O
I/O
OPMODE
[1:0]
01b
00b
10b
00b
00b
00b
10b
00b
Description
active HIGH transmit enable
transmit differential data on DP and DM when TX_ENABLE is HIGH
receive differential data from DP and DM when TX_ENABLE is LOW
transmit single-ended zero on DP and DM when TX_ENABLE is HIGH
receive single-ended zero from DP and DM when TX_ENABLE is LOW
active HIGH interrupt indication; will be asserted whenever any
unmasked interrupt occurs
reserved; the ISP1507 will drive these pins to LOW
Rev. 04 — 20 May 2010
DP_PULL
DOWN
Xb
1b
1b
1b
1b
1b
1b
1b
Table
8. Resistor setting signals are defined as follows:
DM_PULL
DOWN
Xb
1b
1b
1b
1b
1b
1b
1b
ISP1507A; ISP1507B
0b
Internal resistor settings
RPU_
DP_EN
0b
0b
0b
0b
0b
0b
0b
ULPI HS USB OTG transceiver
RPD_
DP_EN
0b
1b
1b
1b
1b
1b
1b
1b
© ST-ERICSSON 2010. All rights reserved.
RPD_
DM_EN
0b
1b
1b
1b
1b
1b
1b
1b
Table 8
will force
HSTERM
_EN
0b
0b
1b
1b
0b
0b
0b
0b
19 of 81