CS5529-AS Cirrus Logic Inc, CS5529-AS Datasheet - Page 17

• Manufacturer Part Number: CS5529-AS
• Description: A/D Converter (A-D) IC
• Manufacturer: Cirrus Logic Inc

Specifications of CS5529-AS

• Peak Reflow Compatible (260 C): No
• Termination Type: SMD
• No. Of Bits: 16 Bit
• Leaded Process Compatible: No
• Mounting Type: Surface Mount
• No. Of Channels: 2
• Interface Type: Serial
• Package / Case: 20-SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Port Flag
The port flag bit in the configuration register allows
the user to select the mode in which conversions
will be presented to the serial port. With the port
flag bit cleared, the user must read the conversion
data register. With the port flag bit set to logic 1, the
user can read the conversion data from the serial
port by first issuing the NULL command to clear
the SDO flag and then issuing 24 SCLKs to read
the conversion word.
Calibration
Calibration is used to set the zero and gain slope of
the ADC’s transfer function. The calibration con-
trol bits in the configuration register allow the user
to perform either self calibration or system calibra-
tion.
The offset and gain calibration steps each take one
conversion cycle to complete. At the end of the cal-
ibration step, the calibration control bits will be set
back to logic 0, and the DF (Done Flag) bit will be
set to a logic 1. For the combination self-calibration
(CC2-CC0= 011; offset calibration followed by
gain calibration), the calibration will take two con-
Offset Register
One LSB represents 2
Offset and data word bits align by MSB (bit MSB-4 of offset register changes bit MSB-4 of data). After reset, all bits
are ‘0’.
DS246F1
23(MSB)
Sign
2
11
0
-13
0
2
2
22
10
0
-14
0
-2
-24
2
2
21
0
9
-15
0
-3
proportion of the input span (bipolar span is 2 times unipolar span).
2
2
20
-16
0
8
0
-4
2
2
19
0
7
-17
0
-5
2
2
18
-18
0
6
0
-6
2
2
17
0
5
-19
0
-7
version cycles to complete and will set the DF bit
after the gain calibration is completed.
Note:
Calibration Registers
The offset calibration result is stored in the offset
register. The result is used during the conversion
process to nullify offset errors. One LSB in the off-
set register is 2
polar span is 2 times the unipolar span). The MSB
in the offset register determines if the offset to be
trimmed is positive or negative (0 positive, 1 nega-
tive). The converter can typically trim ±50 percent
of the input span. Refer to the following Offset
Register and Gain Register descriptions for details.
2
2
16
0
4
-20
0
-8
1) The DF bit will be cleared any time the data
register, the offset register, the gain register,
or the setup register is read. Reading the
configuration register alone will not clear the
DF bit. 2) After the CS5529 is reset, the
converter is functional and can perform
measurements without being calibrated. In
this case, the converter will utilize the
initialized values of the on-chip registers
(Gain = 1.0, Offset = 0.0) to calculate output
words. Any initial offset and gain errors in the
internal circuitry of the chip will remain.
-24
2
2
15
0
3
-21
0
-9
proportion of the input span (bi-
2
2
14
-10
-22
0
2
0
2
2
13
-23
-11
0
1
0
CS5529
2
2
12
-12
-24
0
0
0
17