FC4A-K2C1 IDEC, FC4A-K2C1 Datasheet

no-image

FC4A-K2C1

Manufacturer Part Number
FC4A-K2C1
Description
Analog Output Module
Manufacturer
IDEC
Datasheet

Specifications of FC4A-K2C1

Supply Voltage
24VDC
No. Of Analog Outputs
2
Output Voltage Dc Max
10V
External Height
90mm
Supply Voltage Min
20.4V
Operating Voltage Max
10V
Operating Voltage Min
-10V
External Width
23.25mm
External Depth
70mm
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
MicroSmart CPU Module
FC9Y-B902
FC4A
SERIES
Analog I/O Module
User’s Manual

Related parts for FC4A-K2C1

FC4A-K2C1 Summary of contents

Page 1

... FC9Y-B902 FC4A Analog I/O Module User’s Manual SERIES ...

Page 2

... Read this user’s manual to make sure of correct operation before starting installation, wiring, operation, maintenance, and inspection of the FC4A series MicroSmart analog I/O modules • All MicroSmart modules are manufactured under IDEC’s rigorous quality control system, but users must add a backup or failsafe provision to the control system using the MicroSmart in applications where heavy damage or personal injury may be caused in case the MicroSmart should fail ...

Page 3

... About This Manual This user’s manual primarily describes entire functions, installation, programming, and troubleshooting procedures of the FC4A series MicroSmart analog I/O modules HAPTER ENERAL NFORMATION General information about the analog I/O modules, applicable CPU module system program version, and WindLDR ver- sion ...

Page 4

... Programming WindLDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Analog I/O Control Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Data Register Allocation Numbers for Analog I/O Modules . . . . . . . . . . . . . . . . . . . 4-8 Analog Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Analog Output Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4- HAPTER ROUBLESHOOTING Troubleshooting Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 I NDEX FC4A M PECIFICATIONS W IRING ONTROL S A I/O M ICRO MART NALOG ODULE U ’ ...

Page 5

... Ladder Refresh Type FC4A-J8C1 FC4A-J8AT1 END Refresh Type FC4A-K1A1 Ladder Refresh Type FC4A-K2C1 Ladder Refresh Type When executing ANST macro In the step after ANST macro (always refreshed whether input to ANST off) Maintains output status when the CPU is stopped. Output data can be changed using STPA instruction while the CPU is stopped ...

Page 6

... NFORMATION Applicable CPU Modules and WindLDR Version END refresh type analog I/O modules as many as listed below can be used with any FC4A and FC5A MicroSmart CPU modules and WindLDR versions. Ladder refresh type analog I/O modules can be used with the FC4A and FC5A MicroSmart CPU module system program versions and WindLDR versions as listed below ...

Page 7

... Power LED (PWR) END refresh type FC4A-L03A1, FC4A-L03AP1, FC4A-J2A1, FC4A-K1A1: Turns on when power is supplied to the analog I/O module. (3) Status LED (STAT) Ladder refresh type FC4A-J4CN1, FC4A-J8C1, FC4A-J8AT1, FC4A-K2C1: Indicates the operating status of the analog I/O module. (4) Terminal No. Indicates terminal numbers. (5) Cable Terminal All analog I/O modules have a removable terminal block ...

Page 8

... MC1.5/10-G-3.81BK (Phoenix Contact) 100 times minimum 50 mA (5V DC (5V DC (24V DC (24V DC (24V DC (24V DC) 140g 140g ’ ICRO MART NALOG ODULE SER S FC4A-J2A1 FC4A-K1A1 50 mA (5V DC (5V DC (24V DC (24V DC (24V DC (24V DC) FC4A-J8AT1 FC4A-K2C1 45 mA (5V DC (5V DC (24V DC (24V DC (24V DC (24V DC) 125g 110g M ANUAL ...

Page 9

... Effect of Improper Input Connection Maximum Permanent Allowed Overload (No Damage) Selection of Analog Input Signal Type Calibration or Verification to Maintain Rated Accuracy For Note 1 through Note 4, see page 2-7. FC4A M FC4A-L03A1 / FC4A-J2A1 Voltage Input Current Input 0 to 10V MΩ minimum 10Ω — — ...

Page 10

... Conversion Method Maximum Error at 25°C Cold Junction Input Error Compensation Error Temperature Coefficient Repeatability after Stabilization Time Non-lineality Maximum Error 2-4 FC4A M FC4A-J4CN1 / FC4A-J8C1 Voltage Input Current Input 0 to 10V FC4A-J4CN1: 12Ω 1 MΩ FC4A-J8C1: 100Ω — — ...

Page 11

... Maximum Permanent Allowed Overload (No Damage) Selection of Analog Input Signal Type Calibration or Verification to Maintain Rated Accuracy For Note 1 through Note 4, see page 2-7. FC4A M FC4A-J4CN1 / FC4A-J8C1 Voltage Input Current Input 50000 increments (16 bits) 0.2 mV 0.32 µA Default 50000 Optional: –32768 to 32767 (selectable for each channel) (Note 2) — ...

Page 12

... Crosstalk Isolation Effect of Improper Input Connection Selection of Analog Input Signal Type Calibration or Verification to Maintain Rated Accuracy For Note 1 through Note 4, see page 2-7. 2-6 FC4A M FC4A-J8AT1 NTC –50 to 150°C 100 kΩ maximum 0 maximum 2 ms × channels 10 ms × channels + 1 scan time (Note 1) ...

Page 13

... Impossible ’ ICRO MART NALOG ODULE SER ODULE PECIFICATIONS Ladder Refresh FC4A-K1A1 FC4A-K2C1 –10 to +10V ms/ × channels + 1 scan time ±0.005% of full scale/°C ±0.1% of full scale 50000 increments (16 bits) 0.4 mV 0.32 µA –25000 to 25000 (voltage 50000 (current) Twisted pair cable ...

Page 14

... S ODULE PECIFICATIONS Analog I/O Module Terminal Arrangement and Wiring Diagrams FC4A-L03A1 (Analog I/O Module) — Screw Terminal Type Applicable Terminal Block: • Connect a fuse appropriate for the applied voltage and current draw, at the position shown in the diagram. This is required when equipment containing the MicroSmart is destined for Europe. ...

Page 15

... FC4A-J2A1 (Analog Input Module) — Screw Terminal Type Applicable Terminal Block: FC4A-PMT11P (supplied with the analog input module) • Connect a fuse appropriate for the applied voltage and current draw, at the position shown in the diagram. This is required when equipment containing the MicroSmart is destined for Europe. ...

Page 16

... M S ODULE PECIFICATIONS FC4A-J8C1 (Analog Input Module) — Screw Terminal Type Applicable Terminal Block: • Connect a fuse appropriate for the applied voltage and current draw, at the position shown in the diagram. This is required when equipment containing the MicroSmart is destined for Europe. • Do not connect any wiring to unused terminals. ...

Page 17

... Connect a fuse appropriate for the applied voltage and current draw, at the position shown in the diagram. This is required when equipment containing the MicroSmart is destined for Europe. • Do not connect any wiring to unused terminals. FC4A-K2C1 (Analog Output Module) — Screw Terminal Type Applicable Terminal Block: FC4A-PMT10P (supplied with the analog output module) • ...

Page 18

... Output Circuits FC4A-L03A1, FC4A-L03AP1, FC4A-K1A1 2-12 FC4A M FC4A-J4CN1 CS Input Data + – Input Selection Signal I– FC4A-J8AT1 A B Input Selection Signal FC4A-K2C1 + – I ICRO MART NALOG ODULE SER Current Source 15Ω Current Source V+ I+ – ’ ANUAL ...

Page 19

... Separate the analog I/O lines, particularly resistance thermometer inputs, from motor lines as much as possible to suppress the influence of noises. Separate the analog I/O line from the power line. Analog voltage/current input device Resistance thermometer Analog voltage/current output device FC4A M Fuse 24V DC – – A B’ – ...

Page 20

... M S ODULE PECIFICATIONS Dimensions FC4A-L03A1, FC4A-L03AP1, FC4A-J2A1, FC4A-K1A1, FC4A-K2C1 3.8 FC4A-J4CN1, FC4A-J8C1, FC4A-J8AT1 3.8 2-14 FC4A M 23.5 14.6 *8.5 mm when the clamp is pulled out. 23.5 14.6 *8.5 mm when the clamp is pulled out I ICRO MART NALOG ODULE SER 70.0 70.0 All dimensions in mm. ...

Page 21

... This chapter describes precautions for installing the analog I/O modules in connection with the internal current draw by other expansion modules. For general methods and precautions for installation and wiring of the analog I/O modules, see the FC4A MicroSmart user’s manual (FC9Y-B812). • This equipment is suitable for use in Class I, Division 2, Groups non-hazardous loca- Warning tions only ...

Page 22

... For 2-cable connection UL1015 AWG22 Crimping Tool and Screwdriver Order No. Tool Name Crimping Tool For CPU modules Screwdriver For I/O modules and communication adapter Screw Terminal Tightening Torque 3-2 FC4A M Phoenix Type Order No. AI 1,5 1 0,5 AI-TWIN 2 x 0,75 AI-TWIN 2 x 0,5-8 WH ...

Page 23

... For hardware specifications of analog I/O modules, see page 2-2. System Setup The FC4A and FC5A MicroSmart CPU modules can be used with a maximum of seven expansion I/O modules, which include digital I/O modules and analog I/O modules. Quantity of Applicable Analog I/O Modules ...

Page 24

... Select the slots where analog I/O modules are mounted. All slots are selected to use seven analog I/O modules as default. Click the check box to deselect slots where analog I/O modules are not mounted. When using analog I/O modules on Slots and 7, deselect Slots 2, 4, and 5 as shown below. 4-2 FC4A I ’ ...

Page 25

... FC4A-J4CN1 FC4A-J8C1 FC4A-J8AT1 FC4A-K2C1 In the Configure Parameters dialog box, parameters in white cells are selectable while gray cells indicate default parame- ters. In the white cells, optional values can be selected from a pull-down list or entered by typing required values. Note for PID Instruction Source Operand S4 (process variable) When using the PID instruction, specify the data register number shown under Data in the Confi ...

Page 26

... When you do not use any input or output signal, select the default value or Not used for the channel. Analog I/O Module FC4A-L03A1, FC4A-J2A1 END Refresh Type FC4A-L03AP1 Ladder Refresh Type FC4A-J4CN1, FC4A-J8C1, FC4A-J8AT1, FC4A-K2C1 4-4 FC4A M DR Allocation Allocation range changes automatically. Description × ...

Page 27

... When Celsius or Fahrenheit is selected for thermocouple, resistance thermometer, or thermistor signal types on ladder refresh type analog input modules, the scale value can be selected from ×1, ×10, or ×100 depending on the selected signal type. Using this function, the analog input data can be multiplied to ensure precise control. FC4A ...

Page 28

... Repeat the same steps for other slots. 14. When finished, click the OK button to save changes and exit the Set Analog Module Parameters dialog box. 4-6 FC4A M END Refresh Type Data registers are automatically allocated depending on the slot where the analog I/O module is mounted. ...

Page 29

... Analog Input Data Analog Input Operating Status Analog Output Signal Type Analog Output Data Type Analog Output Data Minimum/Maximum Values Analog Output Data Analog Output Operating Status FC4A M Analog Input Module END Refresh Type Ladder Refresh Type FC4A- FC4A- FC4A- L03AP1 J2A1 J4CN1 ...

Page 30

... Analog output data type Analog output data minimum value Analog output data maximum value – Reserved – Note: Data registers allocated to the unused analog I/O module numbers can be used as ordinary data registers. 4-8 FC4A M END Refresh Type Analog I/O Module No D760 ...

Page 31

... Thermistor parameters (FC4A-J8AT1 only) Analog input data Analog input operating status — Reserved — I ICRO MART NALOG ODULE SER 4: A I/O C NALOG ONTROL FC4A-J8C1 FC4A-J8AT1 FC4A-K2C1 Channel Default R/W CH0 FFh R/W All channels 00h CH0 0 R/W 00FFh R/W CH1 0 R/W ...

Page 32

... A I/O C NALOG ONTROL Ladder Refresh Type Analog Output Module Data Register Allocation (FC4A-K2C1) Data Register Data Size Number Offset (word) +0 (Low Byte (High Byte +10 1 +11 1 +12 3 4-10 FC4A M Parameter Analog output signal type — Reserved — Analog output data configuration Analog output signal type Analog output data confi ...

Page 33

... Binary Data When Binary data is selected as an analog input data type, the analog input is linearly converted into digital data in the range described in the table below. FC4A-L03A1 Type No. FC4A-L03AP1 FC4A-J2A1 Analog Input Data 0 to 4095 FC4A M FC4A- FC4A- FC4A- L03A1 L03AP1 J2A1 X — ...

Page 34

... Celsius and Fahrenheit When Celsius or Fahrenheit is selected as an analog input data type, the analog input data range depends on the analog input signal type, scale value, and the type of the analog input module, FC4A-L03AP1, FC4A-J4CN1, and FC4A-J8AT1. • FC4A-L03AP1 Analog Input Signal Type ...

Page 35

... CPU module. For the filtering function of analog input signals, see page 4-4. Valid values are 0 through 255. Thermistor Parameter Thermistor parameters are enabled when selecting NTC thermistor for the analog input type of the FC4A-J8AT1. The same parameters are specified for four channels: CH0 to CH3 and CH4 to CH7. Channel R0: Thermistor resistance value at the temperature (° ...

Page 36

... Minimum value over bit 1 Bit 5 to Bit 15 0 Reserved 4-14 FC4A M Analog Input Operating Status (END refresh type) Analog Input Operating Status (Ladder refresh type) Normal operation Initializing, changing configuration, hardware initialization error Parameter configuration normal Parameter configuration error ...

Page 37

... FC4A-L03A1 FC4A-L03AP1 0 to 10V — — FC4A-L03A1 FC4A-L03AP1 0 to 4095 Analog output data minimum value to maximum value (–32768 to 32767 I ’ ICRO MART NALOG ODULE SER I/O C NALOG ONTROL FC4A-K1A1 FC4A-K2C1 –10 to +10V DC — X FC4A-K1A1 FC4A-K2C1 –25000 to 25000 0 to 50000 M ANUAL 4-15 ...

Page 38

... Output data error bit 1 Bit 4 to Bit 15 0 Reserved 4-16 FC4A M Analog Output Operating Status (END refresh type) Analog Output Operating Status (Ladder refresh type) Normal operation Initializing, changing configuration, hardware initialization error Parameter configuration normal Parameter configuration error ...

Page 39

... FC4A-D40S3 Slot No.: Thermistor Operation In this example, the input value from the NTC thermistor is calibrated. When the temperature reaches the preset value, the output is turned off. The thermistor temperature is monitored on an analog meter. FC4A M Analog Input Module Output Module (Thermistor) (Tr. Source) FC4A-J8AT1 ...

Page 40

... NALOG ONTROL Wiring Diagram FC4A-J8AT1 (Analog Input Module) • Thermistor Specifications Type No. NT731ATTD103K38J (KOA) Type RO 10,000Ω T0 298K (25°C) B Parameter FC4A-T08S1 (8-point Transistor Source Output Module) External Device FC4A-K1A1 (Analog Output Module) 4-18 FC4A M Fuse 24V DC – NTC Thermistor B NTC 3,800K Terminal No ...

Page 41

... WindLDR Programming Analog I/O modules are programmed using the ANST macro in WindLDR . Program the ANST macro as shown below. • Analog Input Module FC4A-J8AT1 on Slot 1 DR Allocation Range D630 - D694 I/O Channel Item Filter CH0 Data Type Scale CH1 Data Type CH2 ...

Page 42

... A I/O C NALOG ONTROL • Analog Output Module FC4A-K1A1 on Slot 3 DR Allocation Range D760 - D779 I/O Channel Item Signal Type OUT CH0 Data Type Ladder Diagram As shown in the ladder diagram below, when initialize pulse special internal relay M8120 is used for the ANST macro in parallel with another instruction, load M8120 again for the other instruction ...

Page 43

... Changing Analog Output While CPU is Stopped When using the FC4A-K2C1 analog output module, the analog output value can be changed while the CPU module is stopped. To change the analog output value, store a required output value to the memory addresses allocated to the analog output data. ...

Page 44

... A I/O C NALOG ONTROL 4-22 FC4A I ’ ICRO MART NALOG ODULE SER S M ANUAL ...

Page 45

... After changing settings, was the CPU stopped and restarted? YES Are data registers duplicated? NO Call IDEC for assistance. FC4A M Supply the rated power voltage to the YES analog I/O module. See pages 4-14 and 4-16. YES Make sure of correct parameters. NO Stop and restart the CPU to configure the analog I/O settings ...

Page 46

... Signal Type? NO After changing settings, was the CPU stopped and restarted? YES Are data registers duplicated? NO Call IDEC for assistance. 5-2 FC4A M Does the Status NO DR store status code 4 (external power supply error)? NO Does the Status DR store status code 1 (initializing)? NO ...

Page 47

... M module specifications 2-1 mounting hole layout for direct mounting O operating status 4-3 P parts description 2-1 Phoenix 3-2 PID instruction source operand S4 FC4A M PLC status power supply precautions for programming ANST macro programming WindLDR protection type R resistance S screwdriver specifications analog 4-13 general ...

Page 48

... No. 79, Hsin Tai Wu Road, Sec. 1, Hsi-Chih, Taipei County, Taiwan Tel: +886-2-2698-3929 Fax: +886-2-2698-3931 E-mail: service@tw.idec.com SINGAPORE IDEC IZUMI ASIA PTE. LTD. No. 31, Tannery Lane #05-01 Dragon Land Building, Singapore 347788 Tel: +65-6746-1155 Fax: +65-6844-5995 E-mail: info@sg.idec.com www.idec.com ©2006 IDEC CORPORATION. All Rights Reserved. Manual No. FC9Y-B902-0 01/07 ...

Related keywords