ZVT-E-IF 10K3A1 UA (UNITED AUTOMATION), ZVT-E-IF 10K3A1 Datasheet

ZVT-E-IF 10K3A1

Manufacturer Part Number

ZVT-E-IF 10K3A1

Description

SENSOR, TEMPERATURE, ZVT-E-IF

Manufacturer

UA (UNITED AUTOMATION)

Datasheet

1.ZVT-E-IF_10K3A1.pdf (1 pages)

Specifications of ZVT-E-IF 10K3A1

Thermocouple Type

NTC

Operating Temperature Max

65Â°C

Operating Temperature Min

0Â°C

External Length / Height

50mm

Response Time

14s

External Diameter

6.4mm

Lead Length

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 1
Download datasheet (32Kb)

10. Switch and turn dial to required temperature and allow system to heat up to a steady

11. If output remains off, check for open or short circuit in sensor circuit, and if output

12.

CE MARKING

This product carries a “CE” marking. For further information, the see the

RECOMMENDATION section or contact our sales desk.

MAXIMUM OUTPUT RMS CURRENT (A)

Max unit temperature

Without extra heatsink

+Heatsink 100 x 100 x 3mm

+Heatsink 170 x 170 x 3mm

OPERATION

Peel adhesive back off dial and fit over 10mm panel hole.

See the table below for heatsink requirements & expected ambient temperature, to

calculate the maximum current rating.

Check that the voltage rating & sensor type is correct.

For ZVT-16-IF only: Apply a ‘thin smear’ of heatsink paste for good thermal coupling

and Insert unit through 10mm panel hole. Affix dial and extra heatsink as appropriate,

ensuring equipotential bonding (Earth bonding) and tighten front nut..

Before fitting control knob, turn temperature control fully anti-clockwise to the

mechanical stop.

Fit and align control knob to coincide with the dial mark below 0ºC

Make wire connections to rear terminals. To monitor supply and load conditions fit

neons across the relevant terminals.

Note that unit will not operate or indicate correctly and Triac will not latch on with

loads of less than 200W.

Set Prop. Band (internally [25-IF] or via rear panel [16-IF]) fully anti-clockwise.

state. If temperature is unstable turn Prop. Band clockwise in small steps over

several minutes until stable conditions are obtained, characterised by a steady output

On/Off ratio.

stays on, check position of sensor relative to heated zone. The correct sensor

temperature set points for resistance are:-

Do not use Megger or other high voltage equipment as the voltage rating may be

exceeded and damage the internal components.

100ºC @

25ºC @

0ºC @

CONTROLLER & 10K3A1-SENSOR

INSTALLATION INSTRUCTIONS

32.6K

10K

680

INSTALLATION

ZVT-16/25-IF

20ºC

50ºC

65ºC

RoHS Compliant

2002/95/EC

Directive

INSTALLATION

ZVT-16/25-IF

X10612

RECOMMENDATION

The ZVT-E-IF-10K3A1 is an NTC type thermistor, sealed in a stainless steel probe with 1mtr.

of white PTFE sensor connections and earth leads.

It is designed for use with ZVT-16-IF and ZVT-25-IF flicker inhibited power temperature

controllers. See Data sheets X10511 and X10542 respectively.

NOTE:

performance reaction time, i.e. for thermal bonding of sensor to metal heatsink, it is

recommended that heatsink paste is used.

Other documents, which may be appropriate for your applications, are available on request,

CODE

X10229

X10213

X10255

X10511

X10542

AP02/4

NOTE. It is recommended that installation and maintenance of this equipment should be

carried out with reference to the current edition of the I.E.E. Wiring Regulations BS7671, by

suitably qualified/trained personnel. The regulations contain important requirements regarding

the safety of electrical equipment. For International Standards refer to I.E.C. Directive I.E.C.

950.

ORDER CODE:

Good thermal bonding of sensor is required, where appropriate, to ensure controller

IDENTITY

RFI

ITA

SRA

ZVT1/2-16

ZVT1/2-25

COS

State part number: ZVT-E-IF-10K3A1

1Southport Business Park

Kew

Southport, PR8 4HQ

ENGLAND

Page No. 2 of 2

DIMENSIONS AND SPECIFICATIONS

UNITED AUTOMATION LIMITED

DESCRIPTION

Filter recommendation - addressing EMC directive.

Interaction, uses for phase angle and for burst fire control.

Safety requirements - addressing the Low Voltage Directive

(LVD) including :-Thermal data/cooling ; “Live” parts warning

& Earth requirements; Fusing recommendations.

16A Zero voltage Temperature controller

25A Zero voltage Temperature controller

UAL Conditions of sale

Issue 2

APPLICATIONS

Tel: 0044 (0) 1704 – 516500 Main

Tel: 0044 (0) 1704 – 516516 Sales

Fax: 0044 (0) 1704 – 516501

Enquiry@united-automation.com

THIS UNIT MUST BE EARTHED

Date

Enclosed, inhibited flicker sensor.

12/03

Related parts for ZVT-E-IF 10K3A1

Related keywords

ZVT-E-IF 10K3A1 datasheet
ZVT-E-IF 10K3A1 data sheet
ZVT-E-IF 10K3A1 pdf datasheet
ZVT-E-IF 10K3A1 component
ZVT-E-IF 10K3A1 part
ZVT-E-IF 10K3A1 distributor
ZVT-E-IF 10K3A1 RoHS
ZVT-E-IF 10K3A1 datasheet download