SI-HG80DQD BANNER ENGINEERING, SI-HG80DQD Datasheet - Page 2

• Manufacturer Part Number: SI-HG80DQD
• Description: SWITCH, SAFETY INTERLOCK, 1NO/1NC, 3A
• Manufacturer: BANNER ENGINEERING
• Type: Interlockr

Specifications of SI-HG80DQD

• Contact Configuration: SPDT
• Contact Voltage Ac Max: 250V
• Contact Voltage Dc Max: 60V
• Contact Current Ac Max: 3A
• Contact Current Dc Max: 500mA
• Switch Operation: ON-OFF
• Actuator Type: Flexible
• Current, Rating: 3/0.5 AAC/ADC
• Function: Safety
• Ip Rating: IP67
• Number Of Poles: 1
• Number Of Positions: 2
• Termination: Quick Connect
• Voltage, Rating: 250/60 VAC/VDC

Hinge Switches –

In the United States, the functions that Banner safety switches are intended to perform are regulated by the Occupational Safety and Health
Administration (OSHA). Whether or not any particular safety switch installation meets all applicable OSHA requirements depends upon factors
that are beyond the control of Banner Engineering Corp. These factors include the details of how the safety switches are applied, installed, wired,
operated, and maintained.
Banner Engineering Corp. has attempted to provide complete application, installation, operation, and maintenance instructions. This information is
found in the instruction manual packaged with each safety switch. In addition, we suggest that any questions regarding the use or installation of
safety switches be directed to the factory applications department at the telephone numbers or address shown below.
Banner Engineering Corp. recommends that safety switches be applied according to the guidelines set forth in international (ISO/IEC) standards
listed below. Specifically, Banner Engineering Corp. recommends application of these safety switches in a configuration which meets safety
category 4, per ISO 13849 (EN954-1).
In addition, the user of Banner safety switches has the responsibility to ensure that all local, state, and national laws, rules, codes, and regulations
relating to the use of Banner safety switches in any particular application are satisfied. Extreme care is urged that all legal requirements have been
met and that all installations and maintenance instructions are followed.
U.S. Regulations Applicable to Use of Banner Safety Switches
U.S. Standards Applicable to Use of Banner Safety Switches
Applicable European and International Standards
OSHA Code of Federal Regulations: Title 29, Parts 1900 to 1910
ANSI B11
ISO/TR 12100-1
(EN 292-18-2)
ISO 13852 (EN 294)
ISO 13853 (EN 811)
ISO 13849 (EN 954-1)
ISO 13855 (EN 999)
ISO 14119 (EN 1088)
IEC/EN 60204-1
IEC/EN 60947-5-1
P/N 46735 rev. B
Important Information
“Safety of Machinery—Basic Concepts, General Principles for Design”
“Safety of Machinery—Safety Distances to Prevent Danger Zones Being Reached by the Upper Limbs”
“Safety of Machinery—Safety Distances to Prevent Danger Zones Being Reached by the Lower Limbs”
“Safety of Machinery—Safety Related Parts of Control Systems”
“ Safety of Machinery—The Positioning of Protective Equipment in Respect to Approach Speeds of Parts of the
“Safety of Machinery—Interlocking Devices Associated with Guards—Principles for Design and Selection”
“Safety of Machinery—Electrical Equipment of Machines”
“Low Voltage Switchgear—Electromechanical Control Circuit Devices”
Available from:
Human Body”
Available from:
“ Standards for Construction, Care, and Use of Machine Tools”
Available from:
SI-HG80 Series
Toll Free:
Email:
Address:
Superintendent of Documents
Government Printing Office
P.O. Box 371954
Pittsburgh, PA 15250-7954
Tel: [phone]
Safety Director
AMT—The Association for Manufacturing Technology
7901 Westpark Drive
McLean, VA 22102
Tel: [phone]
Global Engineering Documents
15 Inverness Way East
Englewood, CO 80112-5704
Phone: [phone]
Fax: [phone]
1-888-3-SENSOR (1-888-373-6767)
[e-mail]
9714 Tenth Avenue North
Minneapolis, MN 55441
Application Assistance
Regarding the Use of Safety Switches
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]