AFCT-57J5ATPZ Avago Technologies US Inc., AFCT-57J5ATPZ Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
AFCT-57J5ATPZ
Manufacturer Part Number
AFCT-57J5ATPZ
Description
SM BTS DFB SFP Ind-Temp, RoHS
Manufacturer
Avago Technologies US Inc.
Datasheet
1.AFCT-57J5ATPZ.pdf
(18 pages)
Specifications of AFCT-57J5ATPZ
Data Rate
3.072Gbps
Wavelength
1310nm
Applications
General Purpose
Voltage - Supply
2.97 V ~ 3.63 V
Connector Type
LC Duplex
Mounting Type
SFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 10. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
(T
Parameter
Transceiver Internal Temperature
Accuracy
Transceiver Internal Supply
Voltage Accuracy
Transmitter Laser DC Bias Current
Accuracy
Transmitted Average Optical
Output Power Accuracy
Received Optical Input Power
Accuracy
Figure 4. Transceiver timing diagrams (module installed except where noted).
12
t-init: TX DISABLE NEGATED
t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED
t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED
t-fault: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL NOT RECOVERED
* SFP SHALL CLEAR TX_FAULT IN
C
< t_init IF THE FAILURE IS TRANSIENT
= -40°C to 85°C, VccT, VccR = 3.3 V ± 10%)
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
OCCURANCE OF FAULT
TRANSMITTED SIGNAL
OCCURANCE OF FAULT
V
CC
V
CC
T,R > 2.97 V
TX_DISABLE
T,R > 2.97 V
TX_DISABLE
TX_FAULT
TX_DISABLE
TX_FAULT
TX_DISABLE
TX_FAULT
TX_FAULT
INSERTION
t_init
t_reset
t_init
t_fault
t_fault
Symbol
T
V
I
P
P
INT
INT
T
R
INT
t_init*
Min.
±3.0
±0.1
±10
±3.0
±3.0
Units
°C
V
%
dB
dB
t-init: TX DISABLE ASSERTED
t-loss-on & t-loss-off
t-off & t-on: TX DISABLE ASSERTED THEN NEGATED
t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED
* SFP SHALL CLEAR TX_FAULT IN
< t_init IF THE FAILURE IS TRANSIENT
Notes
Temperature is measured internal to the transceiver.
Valid from = -10°C to 85°C case temperature.
Supply voltage is measured internal to the transceiver
and can, with less accuracy, be correlated to
voltage at the SFP Vcc pin. Valid over 3.3 V ± 10%.
I
Coupled into 9/125 μm single-mode fiber. Valid from
100 μW to 500 μW, average.
Coupled from 9/125 μm single-mode fiber. Valid from
15 μW to 500 μW, average.
INT
is better than ±10% of the nominal value.
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
OCCURANCE OF FAULT
V
CC
OPTICAL SIGNAL
TX_DISABLE
T,R > 2.97 V
TX_DISABLE
TX_FAULT
TX_DISABLE
TX_FAULT
TX_FAULT
LOS
t_loss_on
t_off
t_reset
OCCURANCE
OF LOSS
t_init
t_init*
t_on
t_loss_off