AFCT-57J5ATPZ Avago Technologies US Inc., AFCT-57J5ATPZ Datasheet - Page 9

• Manufacturer Part Number: AFCT-57J5ATPZ
• Description: SM BTS DFB SFP Ind-Temp, RoHS
• Manufacturer: Avago Technologies US Inc.

Specifications of AFCT-57J5ATPZ

• Data Rate: 3.072Gbps
• Wavelength: 1310nm
• Applications: General Purpose
• Voltage - Supply: 2.97 V ~ 3.63 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 6. Transmitter and Receiver Electrical Characteristics
(T
Parameter
High Speed Data Input:
High Speed Data Output:
Receiver Contributed Deterministic Jitter
Receiver Contributed Total Jitter
Receiver Electrical Output Rise & Fall Times
Notes:
1. Internally AC coupled and terminated (100 Ohm differential).
2. Internally AC coupled but requires an external load termination (100 Ohm differential).
3. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern.
4. 20%-80% electrical rise & fall times measured with a 500 MHz signal utilizing a 1010 data pattern.
Table 7. Transmitter Optical Characteristics
(T
Parameter
Modulated Optical Output Power (OMA)
Average Optical Output Power
Center Wavelength
Spectral Width – rms
Optical Rise/Fall Time (4.25 Gb/s)
RIN
Transmitter Contributed Total Jitter
Transmitter Contributed Total Jitter
Pout TX_DISABLE Asserted
Notes:
1. Max Pout is the lesser of Class 1 safety limits (CDRH and EN 60825) or receiver power, max.
2. Into 9/125 μm single-mode optical fiber.
3. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern. Contributed TJ is the sum of contrib-
9
C
C
Transmitter Differential Input Voltage (TD +/-)
Receiver Differential Output Voltage (RD +/-)
(20-80%)
(Peak-to-Peak) (0.614 to 3.072 Gb/s)
(0.614 to 3.072Gb/s)
(0.614 to 3.072Gb/s
(0.614 to 3.072Gb/s)
(0.614 to 3.072Gb/s)
uted RJ and contributed DJ. Contributed RJ is calculated for 1x10
from the oscilloscope by 14. Per FC-PI (Table 9 - SM jitter output, note 1), the actual contributed RJ is allowed to increase above its limit if the
actual contributed DJ decreases below its limits, as long as the component output DJ and TJ remain within their specified FC-PI maximum lim-
its with the worst case specified component jitter input.
= -40°C to 85°C, VccT, VccR = 3.3 V ± 10%)
= -40°C to 85°C, VccT, VccR = 3.3 V ± 10%)
12
(OMA)
Symbol
Tx,OMA
Pout
O
V,rms
tr, tf
RIN
DJ
TJ
P
C
OFF
Symbol
V
Vo
DJ
TJ
tr, tf
I
-12
BER by multiplying the RMS jitter (measured on a single rise or fall edge)
Minimum
290
-8.4
1290
30
Minimum
400
600
Typical
350
Typical
Maximum
-3.0
1340
100
-118
50
80
-35
25
200
Maximum
2400
1600
65
Unit
μW
dBm
nm
nm
ps
dB/Hz
ps
ps
dBm
Unit
mV
mV
ps
ps
ps
Notes
Note 2
Note 1, 2
20% - 80%
Notes
Note 1
Note 4
Note 2