AC164142 Microchip Technology, AC164142 Datasheet - Page 21

Consumer-band BPSK 7.2kbps PLM PICtail Plus Daughter Board Other

AC164142

Manufacturer Part Number
AC164142
Description
Consumer-band BPSK 7.2kbps PLM PICtail Plus Daughter Board Other
Manufacturer
Microchip Technology
Series
PICtail™ Plusr
Datasheets

Specifications of AC164142

Kit Application Type
Communication
Silicon Family Name
DsPIC
Kit Contents
2x Power-Line Soft-Modem PICtail Plus Daughter Boards, 2x High Voltage Adapter Cables, Info Sheet
Features
Operates On 5V And 9V
Rohs Compliant
Yes
Processor To Be Evaluated
dsPIC33F
Processor Series
dsPIC33F
Operating Supply Voltage
5 V, 9 V
Featured Product
AC164142 PICtail™ Plus Daughter Board
Main Purpose
Interface, Power Line Transceiver
Embedded
No
Utilized Ic / Part
-
Primary Attributes
AC Power Line Transceiver, BPSK 7.2 Kbps
Secondary Attributes
Requires Explorer 16 Boards
Lead Free Status / Rohs Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AC164142
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
AC164142
Manufacturer:
BOARD
Quantity:
20 000
© 2011 Microchip Technology Inc.
PLM_FEC
This setting enables the Forward Error Correction (FEC) feature. Please note that the
Viterbi algorithm used for the FEC feature requires significant processing power, espe-
cially at higher code constraint lengths. At a carrier frequency of 129.6 kHz, no room is
left to run FEC and this option must be disabled.
PLM_QUALITY_MEASURE
This setting enables received signal quality estimation and determines a 16-bit quality
metric calculated during the initial bytes after the last byte synchronization has been
found. The metric is an average value of absolute values of demodulated signal sam-
ples, taken in the instance of bit decisions during the first 16 bytes after byte
synchronization has been found. A value greater then 0x7F00 means perfect quality.
PLM_LOCAL_ECHO
This setting, if enabled, allows the modem to receive its own transmissions.
PLM_DEBUG_MODE
This setting enables various debugging modes and normally should be off (set to
DEBUG OFF). The other modes supported are:
• Signal Logging mode, where signal samples on various demodulation stages can
• Performance Measurement mode in which a GPIO pin (RG0) is set high
PLM_RAM_SAVING
If enabled, this setting causes the modem code to use less RAM (reduced by a third)
at a cost of consuming more processing power (2 to 4 MIPS). In case this option is
enabled, a processing buffer size must also be selected by manually setting
PLM_DEM_BLOCK_LEN. The smaller the buffer, the smaller the amount of RAM used;
however, the performance hit is more significant.
PLM_ADC
This setting allows the selection of the ADC, in case the dsPIC33F DSC device used
has more than one ADC module.
PLM_USE_DMA
This setting, if set to ‘
there are good reasons not to (e.g., no DMA support in the selected CPU model), DMA
should be used for best performance.
PLM_FC
This setting sets the carrier frequency and must not be changed while using the
daughter board.
PLM_BAUD
This setting sets the modem baud rate. Available options are: 1200, 2400, 3600, 4800,
5400, and 7200 (default).
be saved in a circular buffer
whenever the processor is executing low-level modem code
1
’, causes the code to be compiled with DMA support. Unless
DS70656A-page 21

Related parts for AC164142