AD9520-4BCPZ-REEL7 Analog Devices Inc, AD9520-4BCPZ-REEL7 Datasheet - Page 50

• Manufacturer Part Number: AD9520-4BCPZ-REEL7
• Description: Clock IC With 1.6GHz On-chip VCO
• Manufacturer: Analog Devices Inc
• Type: Clock Generator, Fanout Distributionr

Specifications of AD9520-4BCPZ-REEL7

• Design Resources: Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121) Phase Coherent FSK Modulator (CN0186)
• Pll: Yes
• Input: CMOS, LVDS, LVPECL
• Output: CMOS, LVPECL
• Number Of Circuits: 1
• Ratio - Input:output: 2:12, 2:24
• Differential - Input:output: Yes/Yes
• Frequency - Max: 1.8GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Frequency-max: 1.8GHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD9520-4/PCBZ - BOARD EVAL FOR AD9520-4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD9520-4
When the AD9520 is in a PD power-down, the chip is in the
following state:
•
•
•
•
•
•
•
•
•
PLL Power-Down
The PLL section of the AD9520 can be selectively powered
down. There are two PLL power-down modes set by
Register 0x010[1:0]: asynchronous and synchronous.
In asynchronous power-down mode, the device powers down as
soon as the registers are updated. In synchronous power-down
mode, the PLL power-down is gated by the charge pump to
prevent unwanted frequency jumps. The device goes into power-
down on the occurrence of the next charge pump event after the
registers are updated.
The PLL is off (asynchronous power-down).
The VCO is off.
The CLK input buffer is off, but the CLK input dc bias
circuit is on.
In differential mode, the reference input buffer is off, but
the dc bias circuit is still on.
In singled-ended mode, the reference input buffer is off,
but the dc bias circuit is off.
All dividers are off.
All CMOS outputs are tristated.
All LVPECL outputs are in safe off mode.
The serial control port is active, and the chip responds to
commands.
Rev. 0 | Page 50 of 84
Distribution Power-Down
The distribution section can be powered down by writing
0x230[1] = 1b, which turns off the bias to the distribution
section. If the LVPECL power-down mode is in normal
operation (0b), it is possible for a low impedance load on that
LVPECL output to draw significant current during this power-
down. If the LVPECL power-down mode is set to 1b, the
LVPECL output is not protected from reverse bias and can be
damaged under certain termination conditions.
Individual Clock Output Power-Down
Any of the clock distribution outputs can be powered down
into safe power-down mode by individually writing to the
appropriate registers. The register map details the individual
power-down settings for each output. These settings are found
in 0x0F0[0] to 0x0FD[0].
Individual Clock Channel Power-Down
Any of the clock distribution channels can be powered down
individually by writing to the appropriate registers. Powering
down a clock channel is similar to powering down an individual
driver, but it saves more power because the dividers are also
powered down. Powering down a clock channel also automatically
powers down the drivers connected to it. The register map
details the individual power-down settings for each output
channel. These settings are found in 0x192[2], 0x195[2],
0x198[2], and 0x19B[2].