AD9520-4BCPZ-REEL7 Analog Devices Inc, AD9520-4BCPZ-REEL7 Datasheet - Page 71

• Manufacturer Part Number: AD9520-4BCPZ-REEL7
• Description: Clock IC With 1.6GHz On-chip VCO
• Manufacturer: Analog Devices Inc
• Type: Clock Generator, Fanout Distributionr

Specifications of AD9520-4BCPZ-REEL7

• Design Resources: Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121) Phase Coherent FSK Modulator (CN0186)
• Pll: Yes
• Input: CMOS, LVDS, LVPECL
• Output: CMOS, LVPECL
• Number Of Circuits: 1
• Ratio - Input:output: 2:12, 2:24
• Differential - Input:output: Yes/Yes
• Frequency - Max: 1.8GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Frequency-max: 1.8GHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD9520-4/PCBZ - BOARD EVAL FOR AD9520-4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Reg.
Addr
(Hex) Bit(s) Name
018
019
019
019
01A
01A
01A
[0]
[7:6] R, A, B counters
[5:3] R path delay
[2:0] N path delay
[7]
[6]
[5:0] LD pin control
VCO calibration
now
SYNC pin reset
Enable STATUS
pin divider
Ref freq monitor
threshold
Description
Bit used to initiate the VCO calibration. This bit must be toggled from 0 to 1 in the active registers. The
sequence to initiate a calibration follows: program to 0, followed by an IO_ UPDATE bit (Register 0x232[0]);
then programmed to 1, followed by another IO_ UPDATE bit (Register 0x232[0]). This sequence gives
complete control over when the VCO calibration occurs relative to the programming of other registers that
can impact the calibration (default = 0).
[7]
0
0
1
1
[5:3] R Path Delay, see Table 2, (default: 0x00).
[2:0] N Path Delay, see Table 2, (default: 0x0).
Enables a divide-by-4 on the STATUS pin. This makes it easier to look at low duty-cycle signals out of the
pulse-swallow R and N dividers.
[7] = 0; divide-by-4 disabled on STATUS pin (default).
[7] = 1; divide-by-4 enabled on STATUS pin.
Sets the reference (REF1/REF2) frequency monitor’s detection threshold frequency. This does not affect
the VCO frequency monitor’s detection threshold (see Table 17, REF1, REF2, and VCO frequency status
monitor parameter).
[6] = 0; frequency valid if frequency is above 750 kHz (default).
[6] = 1; frequency valid if frequency is above 6 kHz.
Selects the signal that is connected to the LD pin.
[5] [4] [3]
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
[6]
0
1
0
1
0
0
0
0
0
X
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
Action
Do nothing on SYNC (default).
Asynchronous reset.
Synchronous reset.
Do nothing on SYNC .
[2]
0
0
0
0
1
X
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
[1]
0
0
1
1
0
X
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
Rev. 0 | Page 71 of 84
[0]
0
1
0
1
0
X
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Level or
Dynamic
Signal
LVL
DYN
DYN
HIZ
CUR
LVL
LVL
DYN
DYN
DYN
DYN
LVL
LVL
LVL
LVL
LVL
LVL
LVL
LVL
LVL
LVL
LVL
LVL
DYN
Signal at LD Pin
Digital lock detect (high = lock, low = unlock, default).
P-channel, open-drain lock detect (analog lock detect).
N-channel, open-drain lock detect (analog lock detect).
Tristate (high-Z) LD pin.
Current source lock detect (110 μA when DLD is true).
Ground (dc); for all other cases of 0XXXXX not specified.
The selections that follow are the same as REFMON.
Ground (dc).
REF1 clock (differential reference when in differential mode).
REF2 clock (N/A in differential mode).
Selected reference to PLL (differential reference when in
differential mode).
Unselected reference to PLL (not available in differential mode).
Status of selected reference (status of differential reference);
active high.
Status of unselected reference (not available in differential
mode); active high.
Status REF1 frequency (active high).
Status REF2 frequency (active high).
(Status REF1 frequency) AND (status REF2 frequency).
(DLD) AND (status of selected reference) AND (status of VCO).
Status of VCO frequency (active high).
Selected reference (low = REF1, high = REF2).
DLD; active high.
Holdover active (active high).
N/A, do not use.
VS (PLL supply).
REF1 clock (differential reference when in differential mode).
AD9520-4