ADF4360-7BCPZRL7 Analog Devices Inc, ADF4360-7BCPZRL7 Datasheet - Page 24

• Manufacturer Part Number: ADF4360-7BCPZRL7
• Description: IC,FREQUENCY SYNTHESIZER,BICMOS,LLCC,24PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Type: Fanout Distribution, Integer N Synthesizer (RF)r

Specifications of ADF4360-7BCPZRL7

• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 1:2
• Differential - Input:output: No/No
• Frequency - Max: 1.8GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-LFCSP
• Frequency-max: 1.8GHz
• Number Of Elements: 1
• Pll Input Freq (min): 10MHz
• Pll Input Freq (max): 250MHz
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: LFCSP EP
• Output Frequency Range: 350 to 1800MHz
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Industrial
• Pin Count: 24
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF4360-7EBZ1 - BOARD EVALUATION FOR ADF4360-7
• Lead Free Status / Rohs Status: Compliant

ADF4360-7
OUTPUT MATCHING
There are a number of ways to match the output of the
ADF4360-7 for optimum operation; the most basic is to use a
50 Ω resistor to V
nected in series, as shown in Figure 29. Because the resistor is
not frequency dependent, this provides a good broadband
match. The output power in this circuit typically gives
−5 dBm output power into a 50 Ω load.
A better solution is to use a shunt inductor (acting as an RF
choke) to V
output power. Additionally, a series inductor is added after the
dc bypass capacitor to provide a resonant LC circuit. This tunes
the oscillator output and provides approximately 10 dB addi-
tional rejection of the second harmonic. The shunt inductor
needs to be a relatively high value (>40 nH).
Experiments have shown that the circuit shown in Figure 30
provides an excellent match to 50 Ω over a limited operating
range of the ADF4360-7 (850 MHz to 950 MHz). This gives
approximately −2 dBm output power across the specific
frequency range of the ADF4360-7 using 3.9 nH. For other
frequencies, a tuned LC is recommended. Both complementary
architectures can be examined using the EVAL-ADF4360-7EB1
evaluation board.
VCO
Figure 29. Simple ADF4360-7 Output Stage
. This gives a better match and, therefore, more
RF
VCO
V
VCO
OUT
. A dc bypass capacitor of 100 pF is con-
51Ω
100pF
50Ω
Rev. A | Page 24 of 28
If the user does not need the differential outputs available
on the ADF4360-7, the user may either terminate the unused
output or combine both outputs using a balun. The circuit in
Figure 31 shows how best to combine the outputs.
The circuit in Figure 31 is a lumped-lattice-type LC balun. It
is designed for a center frequency of 900 MHz and outputs
5.0 dBm at this frequency. The series 7.5 nH inductor is used to
tune out any parasitic capacitance due to the board layout from
each input, and the remainder of the circuit is used to shift the
output of one RF input by +90° and the second by −90°, thus
combining the two. The action of the 9.0 nH inductor and the
3.3 pF capacitor accomplishes this. The 47 nH is used to provide
an RF choke to feed the supply voltage, and the 100 pF capacitor
provides the necessary dc block. To ensure good RF perform-
ance, the circuits in Figure 30 and Figure 31 are implemented
with Coilcraft 0402/0603 inductors and AVX 0402 thin-film
capacitors.
Alternatively, instead of the LC balun shown in Figure 31, both
outputs may be combined using a 180° rat-race coupler.
Figure 31. Balun for Combining ADF4360-7 RF Outputs
RF
RF
Figure 30. Optimum ADF4360-7 Output Stage
OUT
OUT
A
B
RF
V
VCO
OUT
7.5nH
7.5nH
V
VCO
47nH
3.9pF
9.0nH
3.3pF
9.0nH
3.3pF
7.5nH
47nH
100pF
50Ω
50Ω