ADSP-21062LAB-160 Analog Devices Inc, ADSP-21062LAB-160 Datasheet - Page 12
![Digital Signal Processor(DSP) IC](/photos/6/71/67191/b-225-2_sml.jpg)
ADSP-21062LAB-160
Manufacturer Part Number
ADSP-21062LAB-160
Description
Digital Signal Processor(DSP) IC
Manufacturer
Analog Devices Inc
Series
SHARC®r
Type
Floating Pointr
Datasheet
1.ADSP-21062KSZ-133.pdf
(64 pages)
Specifications of ADSP-21062LAB-160
Rohs Status
RoHS non-compliant
Interface
Host Interface, Link Port, Serial Port
Clock Rate
40MHz
Non-volatile Memory
External
On-chip Ram
256kB
Voltage - I/o
3.30V
Voltage - Core
3.30V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
225-BGA
Lead Free Status / RoHS Status
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADSP-21062LAB-160
Manufacturer:
AD
Quantity:
201
Company:
Part Number:
ADSP-21062LAB-160
Manufacturer:
Analog Devices Inc
Quantity:
10 000
ADSP-21060/ADSP-21060L/ADSP-21062/ADSP-21062L/ADSP-21060C/ADSP-21060LC
Table 3. Pin Descriptions (Continued)
Pin
TFSx
RFSx
LxDAT3–0
LxCLK
LxACK
EBOOT
LBOOT
BMS
CLKIN
RESET
TCK
TMS
TDI
TDO
TRST
EMU
ICSA
VDD
GND
NC
A = Asynchronous, G = Ground, I = Input, O = Output, P = Power Supply, S = Synchronous, (A/D) = Active Drive, (O/D) = Open Drain,
T = Three-State (when SBTS is asserted, or when the ADSP-2106x is a bus slave)
Type
I/O
I/O
I/O
I/O
I/O
I
I
I/OT
I
I/A
I
I/S
I/S
O
I/A
O
O
P
G
Function
Transmit Frame Sync (Serial Ports 0, 1).
Receive Frame Sync (Serial Ports 0, 1).
Link Port Data (Link Ports 0–5). Each LxDAT pin has a 50 k: internal pull-down resistor that is enabled or
disabled by the LPDRD bit of the LCOM register.
Link Port Clock (Link Ports 0–5). Each LxCLK pin has a 50 k: internal pull-down resistor that is enabled or
disabled by the LPDRD bit of the LCOM register.
Link Port Acknowledge (Link Ports 0–5). Each LxACK pin has a 50 k: internal pull-down resistor that is
enabled or disabled by the LPDRD bit of the LCOM register.
EPROM Boot Select. When EBOOT is high, the ADSP-2106x is configured for booting from an 8-bit EPROM.
When EBOOT is low, the LBOOT and BMS inputs determine booting mode. See the table in the BMS pin
description below. This signal is a system configuration selection that should be hardwired.
Link Boot. When LBOOT is high, the ADSP-2106x is configured for link port booting. When LBOOT is low,
the ADSP-2106x is configured for host processor booting or no booting. See the table in the BMS pin
description below. This signal is a system configuration selection that should be hardwired.
Boot Memory Select. Output: Used as chip select for boot EPROM devices (when EBOOT = 1, LBOOT = 0).
In a multiprocessor system, BMS is output by the bus master. Input: When low, indicates that no booting will
occur and that ADSP-2106x will begin executing instructions from external memory. See table below. This
input is a system configuration selection that should be hardwired. *Three-statable only in EPROM boot
mode (when BMS is an output).
EBOOT
1
0
0
0
0
1
Clock In. External clock input to the ADSP-2106x. The instruction cycle rate is equal to CLKIN. CLKIN should
not be halted, changed, or operated below the minimum specified frequency.
Processor Reset. Resets the ADSP-2106x to a known state and begins program execution at the program
memory location specified by the hardware reset vector address. This input must be asserted (low) at
power-up.
Test Clock (JTAG). Provides an asynchronous clock for JTAG boundary scan.
Test Mode Select (JTAG). Used to control the test state machine. TMS has a 20 k: internal pull-up resistor.
Test Data Input (JTAG). Provides serial data for the boundary scan logic. TDI has a 20 k: internal pull-up
resistor.
Test Data Output (JTAG). Serial scan output of the boundary scan path.
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed low) after power-up or held
low for proper operation of the ADSP-2106x. TRST has a 20 k: internal pull-up resistor.
Emulation Status. Must be connected to the ADSP-2106x EZ-ICE target board connector only.
Reserved, leave unconnected.
Power Supply; nominally 5.0 V dc for 5 V devices or 3.3 V dc for 3.3 V devices. (30 pins).
Power Supply Return. (30 pins).
Do Not Connect. Reserved pins which must be left open and unconnected.
LBOOT
0
0
1
0
1
1
Rev. F | Page 12 of 64 | March 2008
BMS
Output
1 (Input)
1 (Input)
0 (Input)
0 (Input)
x (Input)
Booting Mode
EPROM (Connect BMS to EPROM chip select.)
Reserved
Host Processor
Link Port
No Booting. Processor executes from external memory.
Reserved