ADSP-2183KCA-210 Analog Devices Inc, ADSP-2183KCA-210 Datasheet - Page 10
![Digital Signal Processor(DSP) IC](/photos/6/71/67184/ca-144_sml.jpg)
ADSP-2183KCA-210
Manufacturer Part Number
ADSP-2183KCA-210
Description
Digital Signal Processor(DSP) IC
Manufacturer
Analog Devices Inc
Series
ADSP-21xxr
Type
Fixed Pointr
Datasheet
1.ADSP-2183BSTZ-160.pdf
(31 pages)
Specifications of ADSP-2183KCA-210
Rohs Status
RoHS non-compliant
Interface
Synchronous Serial Port (SSP)
Clock Rate
52MHz
Non-volatile Memory
External
On-chip Ram
80kB
Voltage - I/o
3.30V
Voltage - Core
3.30V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
144-MBGA, 144-Mini-BGA
Device Core Size
16b
Format
Fixed Point
Clock Freq (max)
52MHz
Mips
52
Device Input Clock Speed
52MHz
Ram Size
80KB
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
144
Package Type
CSPBGA
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADSP-2183KCA-210
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
ADSP-2183KCA-210
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ADSP-2183
If Go Mode is enabled, the ADSP-2183 will not halt program
execution until it encounters an instruction that requires an
external memory access.
If the ADSP-2183 is performing an external memory access
when the external device asserts the BR signal, then it will not
three-state the memory interfaces or assert the BG signal until
the processor cycle after the access completes. The instruction
does not need to be completed when the bus is granted. If a
single instruction requires two external memory accesses, the
bus will be granted between the two accesses.
When the BR signal is released, the processor releases the BG
signal, reenables the output drivers and continues program
execution from the point where it stopped.
The bus request feature operates at all times, including when
the processor is booting and when RESET is active.
The BGH pin is asserted when the ADSP-2183 is ready to
execute an instruction, but is stopped because the external bus
is already granted to another device. The other device can re-
lease the bus by deasserting bus request. Once the bus is re-
leased, the ADSP-2183 deasserts BG and BGH and executes
the external memory access.
Flag I/O Pins
The ADSP-2183 has eight general purpose programmable in-
put/output flag pins. They are controlled by two memory
mapped registers. The PFTYPE register determines the direc-
tion, 1 = output and 0 = input. The PFDATA register is used to
read and write the values on the pins. Data being read from a
pin configured as an input is synchronized to the ADSP-2183’s
clock. Bits that are programmed as outputs will read the value
being output. The PF pins default to input during reset.
In addition to the programmable flags, the ADSP-2183 has five
fixed-mode flags, FLAG_IN, FLAG_OUT, FL0, FL1 and FL2.
FL0-FL2 are dedicated output flags. FLAG_IN and FLAG_OUT
are available as an alternate configuration of SPORT1.
INSTRUCTION SET DESCRIPTION
The ADSP-2183 assembly language instruction set has an
algebraic syntax that was designed for ease of coding and read-
ability. The assembly language, which takes full advantage of
the processor’s unique architecture, offers the following benefits:
• The algebraic syntax eliminates the need to remember cryptic
• Every instruction assembles into a single, 24-bit word that can
assembler mnemonics. For example, a typical arithmetic add
instruction, such as AR = AX0 + AY0, resembles a simple
equation.
execute in a single instruction cycle.
• The syntax is a superset ADSP-2100 Family assembly lan-
• Sixteen condition codes are available. For conditional jump,
• Multifunction instructions allow parallel execution of an
DESIGNING AN EZ-ICE-COMPATIBLE SYSTEM
The ADSP-2183 has on-chip emulation support and an ICE-
Port, a special set of pins that interface to the EZ-ICE. These
features allow in-circuit emulation without replacing the target
system processor by using only a 14-pin connection from the
target system to the EZ-ICE. Target systems must have a 14-pin
connector to accept the EZ-ICE’s in-circuit probe, a 14-pin plug.
The ICE-Port interface consists of the following ADSP-2183 pins:
EBR
EMS
ELIN
These ADSP-2183 pins must be connected only to the EZ-ICE
connector in the target system. These pins have no function
except during emulation, and do not require pull-up or pull-
down resistors. The traces for these signals between the ADSP-
2183 and the connector must be kept as short as possible, no
longer than three inches.
The following pins are also used by the EZ-ICE:
BR
RESET
The EZ-ICE uses the EE (emulator enable) signal to take con-
trol of the ADSP-2183 in the target system. This causes the
processor to use its ERESET, EBR and EBG pins instead of the
RESET, BR and BG pins. The BG output is three-stated.
These signals do not need to be jumper-isolated in your system.
The EZ-ICE connects to your target system via a ribbon cable
and a 14-pin female plug. The ribbon cable is 10 inches in
length with one end fixed to the EZ-ICE. The female plug is
plugged onto the 14-pin connector (a pin strip header) on the
target board.
guage and is completely source and object code compatible
with other family members. Programs may need to be relo-
cated to utilize on-chip memory and conform to the ADSP-
2183’s interrupt vector and reset vector map.
call, return or arithmetic instructions, the condition can be
checked and the operation executed in the same instruction
cycle.
arithmetic instruction with up to two fetches or one write to
processor memory space during a single instruction cycle.
EBG
EINT
ELOUT
BG
GND
ERESET
ECLK
EE