WM8983GEFL/RV Wolfson Microelectronics, WM8983GEFL/RV Datasheet - Page 57

• Manufacturer Part Number: WM8983GEFL/RV
• Description: Audio CODECs Mbl Multimedia CODEC w/ 1W Speaker Driver
• Manufacturer: Wolfson Microelectronics

Specifications of WM8983GEFL/RV

• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: QFN-32
• Minimum Operating Temperature: - 25 C

Production Data
w
DIGITAL PLAYBACK (DAC) PATH
Table 28 DAC Enable Control
Table 29 DAC Control Register
AUTO-MUTE
DIGITAL HI-FI DAC VOLUME (GAIN) CONTROL
The analogue outputs from the DACs can then be mixed with the aux analogue inputs and the ADC
analogue inputs. The mix is fed to the output drivers for headphone (LOUT1/ROUT1,
LOUT2/ROUT2) or line (OUT3/OUT4). OUT3 and OUT4 have additional mixers which allow them to
output different signals to the headphone and line outputs.
Digital data is passed to the WM8983 via the flexible audio interface and is then passed through a
variety of advanced digital filters as shown in Figure 30 to the hi-fi DACs. The DACs are enabled by
the DACENL/R register bits.
The WM8983 also has a Soft Mute function, which when enabled, gradually attenuates the volume
of the digital signal to zero. When disabled, the gain will ramp back up to the digital gain setting. This
function is enabled by default. To play back an audio signal, it must first be disabled by setting the
SOFTMUTE bit to zero.
The digital audio data is converted to oversampled bit streams in the on-chip, true 24-bit digital
interpolation filters. The bitstream data enters the multi-bit, sigma-delta DACs, which convert it to a
high quality analogue audio signal. The multi-bit DAC architecture reduces high frequency noise and
sensitivity to clock jitter. It also uses a Dynamic Element Matching technique for high linearity and
low distortion.
The DAC output phase defaults to non-inverted. Setting DACLPOL will invert the DAC output phase
on the left channel and DACRPOL inverts the phase on the right channel.
The DAC has an auto-mute function which applies an analogue mute when 1024 consecutive zeros
are detected. The mute is released as soon as a non-zero sample is detected. Auto-mute can be
disabled using the AMUTE control bit.
The signal volume from each Hi-Fi DAC can be controlled digitally. The gain range is –127dB to 0dB
in 0.5dB steps. The level of attenuation for an eight-bit code X is given by:
0.5 × (X-255) dB for 1 ≤ X ≤ 255;
R10
DAC Control
R3
Power
Management 3
REGISTER
ADDRESS
REGISTER
ADDRESS
BIT
0
1
0
1
2
3
6
BIT
DACPOL
DACRPOL
AMUTE
DACOSR
SOFTMUTE
DACENL
DACENR
LABEL
LABEL
MUTE for X = 0
0
0
0
0
0
0
0
DEFAULT
DEFAULT
Left channel DAC enable
0 = DAC disabled
1 = DAC enabled
Right channel DAC enable
0 = DAC disabled
1 = DAC enabled
Left DAC output polarity:
0 = non-inverted
1 = inverted (180 degrees phase shift)
Right DAC output polarity:
0 = non-inverted
1 = inverted (180 degrees phase shift)
Automute enable
0 = Amute disabled
1 = Amute enabled
DAC oversampling rate:
0 = 64x (lowest power)
1 = 128x (best performance)
Softmute enable:
0 = Enabled
1 = Disabled
DESCRIPTION
DESCRIPTION
PD Rev 4.0 November 2006
WM8983
57