LAN91C110-PU SMSC, LAN91C110-PU Datasheet - Page 19

• Manufacturer Part Number: LAN91C110-PU
• Description: Ethernet ICs Non-PCI 10/100 Ethernet MAC
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN91C110-PU

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 5 V
• Supply Voltage (min): 0 V
• Supply Current (max): 40 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-144
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

BANK 0
This register holds bits programmed by the CPU to control some of the protocol transmit options.
SWFDUP - Enables Switched Full Duplex mode. In this mode, transmit state machine is inhibited from recognizing carrier
sense, so deferrals will not occur. Also inhibits collision count, therefore, the collision related status bits in the EPHSR are
not valid (CTR_ROL, LATCOL, SQET, 16COL, MUL COL, and SNGL COL). Uses COL100 as flow control, limiting
backoff and jam to 1 clock each before inter-frame gap, then retry will occur after IFG. If COL100 is active during
preamble, full preamble will be output before jam. When SWFDUP is high, the values of FDUPLX and MON_CSN have
no effect. This bit should be low for non-MII operation.
EPH_LOOP - Internal loopback at the EPH block. Serial data is internally looped back when set. Defaults low. When
EPH_LOOP is high the following transmit outputs are forced inactive: TXD0-TXD3 = 0h, TXEN100 = TXEN = 0, TXD = 1.
The following and external inputs are blocked: CRS=CRS100=0, COL=COL100=0, RX_DV= RX_ER=0.
STP_SQET - Stop transmission on SQET error. If set, stops and disables transmitter on SQE test error. Does not stop on
SQET error and transmits next frame if clear. Defaults low.
FDUPLX - When set the LAN91C110 will cause frames to be received if they pass the address filter regardless of the
source for the frame. When clear the node will not receive a frame sourced by itself. This bit does not control the duplex
mode operation, the duplex mode operation is controlled by the SWFDUP bit.
NOCRC - Does not append CRC to transmitted frames when set. Allows software to insert the desired CRC. Defaults to
zero, namely CRC inserted.
PAD_EN - When set, the LAN91C110 will pad transmit frames shorter than 64 bytes with 00. For TX, CPU should write
the actual BYTE COUNT before padded by the LAN91C110 to the buffer RAM, excludes the padded 00. When this bit is
cleared, the LAN91C110 does not pad frames.
FORCOL - When set, the FORCOL bit will force a collision by not deferring deliberately. This bit is set and cleared only
by the CPU. When TXENA is enabled with no packets in the queue and while the FORCOL bit is set, the LAN91C110 will
transmit a preamble pattern the next time a carrier is seen on the line. If a packet is queued, a preamble and SFD will be
transmitted. This bit defaults low to normal operation. NOTE: The LATCOL bit in the EPHSR, setting up as a result of
FORCOL, will reset TXENA to 0. In order to force another collision, TXENA must be set to 1 again.
TXENA
the current transmission before stopping. When stopping due to an error, this bit is automatically cleared.
SMSC LAN91C110 Rev. B
BYTE
BYTE
HIGH
LOW
OFFSET
- Transmit enabled when set. Transmit is disabled if clear. When the bit is cleared the LAN91C110 will complete
SWFDUP
0
PAD_EN
0
0
Reserved
Reserved
TRANSMIT CONTROL
0
0
REGISTER
NAME
Reserved
LOOP
EPH
0
0
DATASHEET
Reserved
Page 19
SQET
STP
FEAST Fast Ethernet Controller for PCMCIA and Generic 16-Bit Applications
0
0
READ/WRITE
Reserved
TYPE
FDUPLX
0
0
Reserved
FORCOL
0
0
SYMBOL
TCR
Reserved
Reserved
Revision 1.0 (11-04-08)
0
0
NOCRC
Datasheet
TXENA
0
0