PIC24FJ16MC102-I/SO Microchip Technology, PIC24FJ16MC102-I/SO Datasheet - Page 93

• Manufacturer Part Number: PIC24FJ16MC102-I/SO
• Description: 16-bit Motor Control Family, 16 MIPS, 16KB Flash, 1KB RAM 28 SOIC .300in TUBE
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ16MC102-I/SO

• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Program Memory Type: Flash
• Program Memory Size: 16 KB
• Data Ram Size: 1 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SOIC-28
• Development Tools By Supplier: MPLAB IDE Software
• Minimum Operating Temperature: - 40 C
• Featured Product: PIC24FJ/33FJ MCUs & dsPIC® DSCs
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 16 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 21
• Eeprom Size: -
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Lead Free Status / Rohs Status: Details

8.0
FIGURE 8-1:
© 2011 Microchip Technology Inc.
Note 1: This data sheet summarizes the features
Note 1:
SOSCO
R
SOSCI
(1)
2: It
3: Some registers and associated bits
2:
OSCILLATOR
CONFIGURATION
OSC1
OSC2
Oscillator
TUN<5:0>
of the PIC24FJ16MC101/102 family of
devices. It is not intended to be a
comprehensive reference source. To
complement the information in this data
sheet, refer to Section 6. “Oscillator”
(DS39700)
Reference Manual”, which is available
from
(www.microchip.com).
specifications in
cal Characteristics”
supercede any specifications that may be
provided in PIC24F Family Reference
Manual sections.
described in this section may not be
available on all devices. Refer to
Section 4.0 “Memory Organization”
this data sheet for device-specific register
and bit information.
If the Oscillator is used with MS or HS modes, an extended parallel resistor with the value of 1 MΩ must be connected.
The term F
F
doze ratio of 1:2 or lower.
P
FRC
and F
Primary Oscillator (P
Secondary Oscillator (S
is
POSCMD<1:0>
CY
important
Oscillator
the
P
are used interchangeably, except in the case of DOZE mode. F
LPRC
refers to the clock source for all peripherals, while F
PIC24FJ16MC101/102 OSCILLATOR SYSTEM DIAGRAM
in
Microchip
LPOSCEN
the
Section 26.0 “Electri-
OSC
S1
to
÷ 16
S3
)
OSC
of this data sheet,
“PIC24F
note
)
FRCDIV<2:0>
web
that
Family
4x PLL
site
the
Preliminary
in
MSPLL, ECPLL,
FRCPLL
Clock Fail
MS, HS, EC
CY
S7
FRCDIV16
The PIC24FJ16MC101/102 oscillator system provides:
• External and internal oscillator options as clock
• An on-chip 4x Phase-Locked Loop (PLL) to scale
• An internal FRC oscillator that can also be used
• Clock switching between various clock sources
• Programmable clock postscaler for system power
• A Fail-Safe Clock Monitor (FSCM) that detects
• A Clock Control register (OSCCON)
• Nonvolatile Configuration bits for main oscillator
A simplified diagram of the oscillator system is shown
in
FRCDIVN
refers to the clock source for the CPU. Throughout this document,
sources
the internal operating frequency to the required
system clock frequency
with the PLL, thereby allowing full-speed
operation without any external clock generation
hardware
savings
clock failure and takes fail-safe measures
selection
Figure
SOSC
LPRC
FRC
PIC24FJ16MC101/102
P
Clock Switch
NOSC<2:0> FNOSC<2:0>
8-1.
and F
S1/S3
S7
S0
S5
S4
S2
S6
CY
are different when DOZE mode is used with a
÷ 2
Reset
DOZE<2:0>
WDT, PWRT, FSCM
DS39997B-page 93
(To peripherals)
Timer 1
F
F
Fosc
CY
P
(2)
(2)