ISP1507FBS,518 NXP Semiconductors, ISP1507FBS,518 Datasheet - Page 29

• Manufacturer Part Number: ISP1507FBS,518
• Description: RF Transceiver USB 2.0 ULPI TRNSCVR
• Manufacturer: NXP Semiconductors

Specifications of ISP1507FBS,518

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Single
• Operating Supply Voltage (typ): 3.3V
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Compliant
• Other names: 935285499518 ISP1507FBS-T

NXP Semiconductors
ISP1507E_ISP1507F_1
Product data sheet
9.5.2.4 RxEvent encoding
Standard USB peripheral controllers:
when V
start and end of USB peripheral operations. Detection of A_VBUS_VLD and SESS_END
thresholds is not needed for standard peripherals.
OTG devices:
provide a minimum of 8 mA on V
there is no need for an overcurrent detection circuit because the internal A_VBUS_VLD
comparator is sufficient. If the OTG A-device provides more than 100 mA on V
overcurrent detector must be used and
27
initiating V
When an OTG device is configured as an OTG B-device, SESS_VLD must be used to
detect when V
when V
pulsing SRP.
The RxEvent field (see
packets received on the USB bus. RxActive and RxError are defined in USB 2.0
Transceiver Macrocell Interface (UTMI) Specification Ver. 1.05 . HostDisconnect is defined
in UTMI+ Specification Rev. 1.0 . A short definition is also given in the following
subsections.
Table 15.
RxActive:
RxActive event to the link. An RxActive event can be communicated using two methods.
The first method is for the ISP1507 to simultaneously assert DIR and NXT. The second
method is for the ISP1507 to send an RXCMD to the link with the RxActive field in
RxEvent bits set to logic 1. The link must be able to detect both methods. RxActive frames
the receive packet from the first byte to the last byte.
The link must assume that RxActive is set to logic 0 when indicated in an RXCMD or when
DIR is deasserted, whichever occurs first.
The link uses RxActive to time high-speed packets and ensure that bus turnaround times
are met. For more information on the USB packet timing, see
RxError:
deasserts NXT and sends an RXCMD with the RxError field set to logic 1. The received
packet is no longer valid and must be dropped by the link.
HostDisconnect:
HostDisconnect is valid only when the ISP1507 is configured as a host (both
DP_PULLDOWN and DM_PULLDOWN are set to logic 1), and indicates to the host
controller when a peripheral is connected or disconnected. The host controller must
Value
00
01
11
10
applies. The OTG A-device also uses SESS_VLD to detect when an OTG B-device is
BUS
BUS
When the ISP1507 has detected an error while receiving a USB packet, it
BUS
Encoded USB event signals
When the ISP1507 has detected a SYNC pattern on the USB bus, it signals an
is at a sufficient level for operation. SESS_VLD must be enabled to detect the
has dropped to a LOW level, allowing the B-device to safely initiate V
BUS
pulsing SRP.
When an OTG device is configured as an OTG A-device, it must be able to
is at a sufficient level for operation. SESS_END must be used to detect
HostDisconnect is encoded into the RxEvent field of the RXCMD.
RxActive
0
1
1
X
Table
Rev. 01 — 28 May 2008
15) of the RXCMD informs the link of information related
BUS
. If the OTG A-device provides less than 100 mA, then
Section “Standard USB host controllers” on page
Standard peripherals must be able to detect
RxError
0
0
1
X
ISP1507E; ISP1507F
ULPI HS USB OTG transceiver
Section
HostDisconnect
0
0
0
1
9.8.1.
© NXP B.V. 2008. All rights reserved.
BUS
BUS
, an
28 of 78