ISP1507FBS,518 NXP Semiconductors, ISP1507FBS,518 Datasheet - Page 8

• Manufacturer Part Number: ISP1507FBS,518
• Description: RF Transceiver USB 2.0 ULPI TRNSCVR
• Manufacturer: NXP Semiconductors

Specifications of ISP1507FBS,518

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Single
• Operating Supply Voltage (typ): 3.3V
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Compliant
• Other names: 935285499518 ISP1507FBS-T

NXP Semiconductors
7. Functional description
ISP1507E_ISP1507F_1
Product data sheet
7.1 ULPI controller
7.2 USB data serializer and deserializer
7.3 Hi-Speed USB (USB 2.0) ATX
The ISP1507 provides an 8-pin interface that is compliant with UTMI+ Low Pin Interface
(ULPI) Specification Rev. 1.1 . This interface must be connected to the USB link.
The ULPI controller provides the following functions:
For more information on the ULPI protocol, see
The USB data serializer prepares data to transmit on the USB bus. To transmit data, the
USB link sends a transmit command and data on the ULPI bus. The serializer performs
parallel-to-serial conversion, bit stuffing and NRZI encoding. For packets with a PID, the
serializer adds a SYNC pattern to the start of the packet, and an EOP pattern to the end
of the packet. When the serializer is busy and cannot accept any more data, the ULPI
controller deasserts NXT.
The USB data deserializer decodes data received from the USB bus. When data is
received, the deserializer strips the SYNC and EOP patterns, and then performs
serial-to-parallel conversion, NRZI decoding and discarding of stuff bits on the data
payload. The ULPI controller sends data to the USB link by asserting DIR, and then
asserting NXT whenever a byte is ready. The deserializer also detects various receive
errors, including bit stuff errors, elasticity buffer underrun or overrun, and byte-alignment
errors.
The Hi-Speed USB ATX block is an analog front-end containing the circuitry needed to
transmit, receive and terminate the USB bus in high-speed, full-speed and low-speed, for
USB peripheral, host and OTG implementations. The following circuitry is included:
•
•
•
•
•
•
•
•
•
•
•
•
•
ULPI-compliant interface and register set
Allows full control over the USB peripheral, host and OTG functionality
Parses the USB transmit and receive data
Prioritizes the USB receive data, USB transmit data, interrupts and register operations
Control of the V
V
Low-power mode
3-pin serial mode
Generates RXCMDs (status updates)
Maskable interrupts
Control over the ULPI bus state; can attach weak pull-down resistors to DATA[3:0]
Differential drivers to transmit data at high-speed, full-speed and low-speed
Differential and single-ended receivers to receive data at high-speed, full-speed and
low-speed
BUS
monitoring, charging and discharging
BUS
Rev. 01 — 28 May 2008
charge pump or external source
ISP1507E; ISP1507F
Section
9.
ULPI HS USB OTG transceiver
© NXP B.V. 2008. All rights reserved.
7 of 78