HFCT-5961TG Avago Technologies US Inc., HFCT-5961TG Datasheet - Page 10

• Manufacturer Part Number: HFCT-5961TG
• Manufacturer: Avago Technologies US Inc.

Specifications of HFCT-5961TG

• Optical Fiber Type: TX/RX
• Data Transfer Rate: 155Mbps
• Optical Rise Time: 2ns
• Optical Fall Time: 2ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 1360nm
• Package Type: DIP With Connector
• Operating Supply Voltage (min): 3.1V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.5V
• Output Current: 50mA
• Operating Temp Range: 0C to 70C
• Mounting: Snap Fit To Panel
• Pin Count: 10
• Lead Free Status / RoHS Status: Compliant

Figure 8. Recommended Panel Mounting
Process plug
This transceiver is supplied with a process plug for
protection of the optical port within the LC connector
receptacle. This process plug prevents contamination
during wave solder and aqueous rinse as well as during
handling, shipping and storage. It is made of a high-
temperature, molded sealing material that can with-
stand +85 °C, and a rinse pressure of 110 lbs per square
inch.
The process plug should only be used once. After re-
moving it from the transceiver, it must not be used
again as a process plug; however, if it has not been con-
taminated it can be reused as a dust cover.
Package and Handling Instructions
Flammability
The HFCT-5961TL/TG/NL/NG/ATL/ATG transceiver hous-
ing consists of high strength, heat resistant and UL 94
V-0 flame retardant plastic and metal packaging.
Recommended Solder and Wash Process
The HFCT-5961TL/TG/NL/NG/ATL/ATG are compatible
with industry-standard wave solder processes.
10
(0.4 ±0.004)
DIMENSIONS IN MILLIMETERS (INCHES)
1.
2.
10.16 ±0.1
FIGURE DESCRIBES THE RECOMMENDED FRONT PANEL OPENING FOR A LC OR SG SFF TRANSCEIVER.
SFF TRANSCEIVER PLACED AT 15.24 mm (0.6) MIN. SPACING.
(0.56 ±0.004)
14.22 ±0.1
15.24
DETAIL A
(0.6)
TOP OF PCB
15.24
(0.6)
B
(0.039)
(0.62 MAX. 0.59 MIN.)
15.75 MAX. 15.0 MIN.
1
A
SECTION B - B
SOLDER POSTS
Recommended Solder fluxes
Solder fluxes used with the HFCT-5961TL/TG/NL/NG/
ATL/ATG should be water-soluble, organic fluxes. Rec-
ommended solder fluxes include Lonco 3355-11 from
London Chemical West, Inc. of Burbank, CA, and 100
Flux from Alpha-Metals of Jersey City, NJ.
Recommended Cleaning/Degreasing Chemicals
Alcohols: methyl, isopropyl, isobutyl.
Aliphatics: hexane, heptane
Other: naphtha.
Do not use partially halogenated hydrocarbons such as
1,1.1 trichloroethane, ketones such as MEK, acetone,
chloroform, ethyl acetate, methylene dichloride, phenol,
methylene chloride, or N-methylpyrolldone. Also, Avago
Technologies does not recommend the use of cleaners
that use halogenated hydrocarbons because of their
potential environmental harm.
LC SFF Cleaning Recommendations
In the event of contamination of the optical ports, the
recommended cleaning process is the use of forced
nitrogen. If contamination is thought to have remained,
the optical ports can be cleaned using a NTT interna-
tional Cletop stick type (diam. 1.25 mm) and HFE7100
cleaning fluid.
B