HFCT-5961TG Avago Technologies US Inc., HFCT-5961TG Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
HFCT-5961TG
Manufacturer Part Number
HFCT-5961TG
Description
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HFCT-5961TG.pdf
(16 pages)
Specifications of HFCT-5961TG
Optical Fiber Type
TX/RX
Data Transfer Rate
155Mbps
Optical Rise Time
2ns
Optical Fall Time
2ns
Operating Temperature Classification
Commercial
Peak Wavelength
1360nm
Package Type
DIP With Connector
Operating Supply Voltage (min)
3.1V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.5V
Output Current
50mA
Operating Temp Range
0C to 70C
Mounting
Snap Fit To Panel
Pin Count
10
Lead Free Status / RoHS Status
Compliant
Regulatory Compliance
The Regulatory Compliance for transceiver performance
is shown in Table 1. The overall equipment design will
determine the certification level. The transceiver perfor-
mance is offered as a figure of merit to assist the design-
er in considering their use in equipment designs.
Electrostatic Discharge (ESD)
There are two design cases in which immunity to ESD
damage is important.
The first case is during handling of the transceiver prior
to mounting it on the circuit board. It is important to
use normal ESD handling precautions for ESD sensitive
devices. These precautions include using grounded
wrist straps, work benches, and floor mats in ESD con-
trolled areas.
The second case to consider is static discharges to the
exterior of the equipment chassis containing the trans-
ceiver parts. To the extent that the LC connector recep-
tacle is exposed to the outside of the equipment chassis
it may be subject to whatever system-level ESD test
criteria that the equipment is intended to meet.
Electromagnetic Interference (EMI)
Most equipment designs utilizing these high-speed
transceivers from Avago Technologies will be required
to meet FCC regulations in the United States, CENELEC
EN55022 (CISPR 22) in Europe and VCCI in Japan. Refer
to EMI section (page 9) for more details.
Table 1: Regulatory Compliance - Targeted Specification
11
Feature
Electrostatic Discharge (ESD)
to the Electrical Pins
Electrostatic Discharge (ESD)
to the LC Receptacle
Electromagnetic
Interference (EMI)
Immunity
Laser Eye Safety and
Equipment Type Testing
Component Recognition
Test Method
MIL-STD-883
Method 3015
Variation of IEC 61000-4-2
FCC Class B
Variation of IEC 61000-4-3
FDA CDRH 21-CFR 1040
Class 1
IEC 60825-1
Amendment 2 2001-01
Underwriters Laboratories and
Canadian Standards Association
Joint Component Recognition for
Information Technology Equipment
Including Electrical Business Equip-
ment.
Immunity
Transceivers will be subject to radio-frequency elec-
tromagnetic fields following the IEC 61000-4-3 test
method.
Eye Safety
These laser-based transceivers are classified as AEL Class
I (U.S. 21 CFR(J) and AEL Class 1 per EN 60825-1 (+A11).
They are eye safe when used within the data sheet lim-
its per CDRH. They are also eye safe under normal oper-
ating conditions and under all reasonably foreseeable
single fault conditions per EN60825-1. Avago Technolo-
gies has tested the transceiver design for compliance
with the requirements listed below under normal op-
erating conditions and under single fault conditions
where applicable. TUV Rheinland has granted certifica-
tion to these transceivers for laser eye safety and use in
EN 60825-2 applications. Their performance enables the
transceivers to be used without concern for eye safety
up to 3.5 V transmitter V
Performance
Class 1 (>500 V).
Tested to 8 kV contact discharge.
Margins are dependent on customer board and chassis
designs.
Typically show no measurable effect from a 10 V/m field
swept from 27 to 1000 MHz applied to the transceiver
without a chassis enclosure.
Accession Number:
License Number:
UL File Number: E173874, 01SC14051
HFCT-5961TL/TG/ATL/ATG ) 933/510116/02 31 July 2001
HFCT-5961NL/NG ) 933/510116/01 26 July 2001
HFCT-5961TL/TG/ATL/ATG ) 9521220-47
CC
.
HFCT-5961NL/NG ) 9521220-46