MT48LC64M8A2TG-7E:C TR Micron Technology Inc, MT48LC64M8A2TG-7E:C TR Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT48LC64M8A2TG-7E:C TR
Manufacturer Part Number
MT48LC64M8A2TG-7E:C TR
Description
Manufacturer
Micron Technology Inc
Type
SDRAMr
Datasheet
1.MT48LC64M8A2TG-7EC_TR.pdf
(68 pages)
Specifications of MT48LC64M8A2TG-7E:C TR
Organization
64Mx8
Density
512Mb
Address Bus
15b
Access Time (max)
5.4ns
Maximum Clock Rate
133MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
125mA
Pin Count
54
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Not Compliant
Table 3:
PDF: 09005aef809bf8f3/Source: 09005aef80818a4a
512MbSDRAM.fm - Rev. L 10/07 EN
2, 4, 5, 7, 8,
3, 9, 43, 49
23–26, 29–
34, 22, 35,
10, 11, 13,
42, 44, 45,
47, 48, 50,
2, 5, 8, 11,
44, 47, 50,
Numbers
18, 17, 16
28, 41, 54
5, 11, 44,
6, 12, 46,
1, 14, 27
15, 39
20, 21
51, 53
Pin
38
37
19
39
36
53
50
40
52
DQ0–DQ15
CAS#, WE#
Pin Descriptions
DQ0–DQ7
DQ0–DQ3
Symbols
BA0, BA1
A0–A12
DQML,
DQMH
x4, x8:
RAS#,
V
DQM
V
x16:
CLK
CKE
V
CS#
V
NC
DD
SS
DD
SS
Q
Q
x16: I/O
Supply
Supply
Supply
Supply
x8: I/O
x4: I/O
Input
Input
Input
Input
Input
Input
Input
Type
–
Clock: CLK is driven by the system clock. All SDRAM input signals are sampled on
the positive edge of CLK. CLK also increments the internal burst counter and
controls the output registers.
Clock enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal.
Deactivating the clock provides PRECHARGE power-down and SELF REFRESH
operation (all banks idle), ACTIVE power-down (row active in any bank), or CLOCK
SUSPEND operation (burst/access in progress). CKE is synchronous except after the
device enters power-down and self refresh modes, where CKE becomes
asynchronous until after exiting the same mode. The input buffers, including CLK,
are disabled during power-down and self refresh modes, providing low standby
power. CKE may be tied HIGH.
Chip select: CS# enables (registered LOW) and disables (registered HIGH) the
command decoder. All commands are masked when CS# is registered HIGH. CS#
provides for external bank selection on systems with multiple banks. CS# is
considered part of the command code.
Command inputs: RAS#, CAS#, and WE# (along with CS#) define the command
being entered.
Input/output mask: DQM is an input mask signal for write accesses and an output
enable signal for read accesses. Input data is masked when DQM is sampled HIGH
during a WRITE cycle. The output buffers are placed in a High-Z state (two-clock
latency) when DQM is sampled HIGH during a READ cycle. On the x4 and x8, DQML
(Pin 15) is a NC and DQMH is DQM. On the x16, DQML corresponds to DQ0–DQ7,
and DQMH corresponds to DQ8–DQ15. DQML and DQMH are considered same
state when referenced as DQM.
Bank address inputs: BA0 and BA1 define to which bank the ACTIVE, READ, WRITE,
or PRECHARGE command is being applied.
Address inputs: A0–A12 are sampled during the ACTIVE command (row-address
A0–A12) and READ/WRITE command (column-address A0–A9, A11, A12 [x4]; A0–
A9, A11 [x8]; A0–A9 [x16]; with A10 defining auto precharge) to select one location
out of the memory array in the respective bank. A10 is sampled during a
PRECHARGE command to determine whether all banks are to be precharged (A10
[HIGH]) or bank selected by (A10 [LOW]). The address inputs also provide the op-
code during a LOAD MODE REGISTER command.
Data input/output: Data bus for x16 (4, 7, 10, 13, 15, 42, 45, 48, and 51 are NCs for
x8; 2, 4, 7, 8, 10, 13, 15, 42, 45, 47, 48, 51, and 53 are NCs for x4).
Data input/output: Data bus for x8 (2, 8, 47, and 53 are NCs for x4).
Data input/output: Data bus for x4.
No connect: This pin should be left unconnected.
DQ power: Isolated DQ power to the die for improved noise immunity.
DQ ground: Isolated DQ ground to the die for improved noise immunity.
Power supply: +3.3V ±0.3V.
Ground.
10
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Description
512Mb: x4, x8, x16 SDRAM
General Description
©2000 Micron Technology, Inc. All rights reserved.