PAXI0000 Red Lion Controls, PAXI0000 Datasheet - Page 29

• Manufacturer Part Number: PAXI0000
• Description: 1/8 DIN DIGITAL INPUT PANEL METE
• Manufacturer: Red Lion Controls
• Series: PAXr
• Type: Multimeterr

Specifications of PAXI0000

• Display Style: Red Characters, Black Background
• Display Type: LED
• Display Face Size: 3.80" L x 1.95" W (96.5 x 49.5mm)
• Display Digits: 6
• Display Digits - Height: 0.560" (14.22mm)
• Mounting Type: Panel Mount
• Termination: Terminal Block
• Voltage - Supply: 85 ~ 250VAC
• No. Of Digits / Alpha: 6
• Signal Input Type: Pulse
• Character Size: 0.56"
• Ip/nema Rating: IP65 / NEMA 4X
• Panel Cutout Height: 1.77"
• Display Font Color: Red
• Panel Cutout Width: 3.62"
• Accuracy: ±0.01% %
• Connection Type: Cage-Clamp
• Cut Out, Panel: 1/8 DIN
• Digit Height: 0.56
• Dimensions: 4.2"L×3.8"W×1.95"H
• Display Digit Height: 0.56 "
• Function: Counter/Rate Indicator
• Indicator Type: Counter/Rate Indicator
• Number Of Digits: 5
• Primary Type: Electronic
• Range, Measurement: ±99999999
• Special Features: Programmable Function Keys
• Temperature, Operating, Range: 0 to 50 °C
• Voltage, Supply: 85 to 250 VAC
• Counter Supply Voltage: 85-250VAC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Backlight: -
• Measuring Range: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: Q4600348

PAXI: CALIBRATION
using Module 5 and the Rate value is scaled using Module 4. If the meter appears
to be indicating incorrectly or inaccurately, refer to the Troubleshooting section.
should be performed by qualified technicians using appropriate equipment.
Calibration does not change any user programmed parameters.
exiting Module 9. In this case, the existing calibration settings remain in effect.
Note: Allow a 30 minute warm-up period before staring calibration.
TROUBLESHOOTING
When Analog Out recalibration is required (generally every 2 years), it
Calibration may be aborted by disconnecting power to the meter before
Shaded areas are model dependent.
PROBLEM
NO DISPLAY
PROGRAM LOCKED-OUT
CERTAIN DISPLAYS ARE LOCKED OUT
INCORRECT DISPLAY VALUE or NOT
COUNTING
USER INPUT NOT WORKING CORRECTLY
OUTPUT DOES NOT WORK
JITTERY DISPLAY
“
MODULES or PARAMETERS NOT ACCESSIBLE
ERROR CODE (
SERIAL COMMUNICATIONS
” RATE
is the Analog Output. The Count A and B values are scaled
using the parameters in Module 1, Counter C value is scaled
The only item in the PAXI meter that can be calibrated
For further assistance, contact technical support at the appropriate company numbers listed.
)
REMEDIES
CHECK: Power level, power connections
CHECK: Active (lock-out) user input
ENTER: Security code requested
CHECK: Module 3 programming
CHECK: Input wiring, DIP switch setting, input programming, scale factor calculation,
CHECK: User input wiring, user input jumper, user input being used for signal, Module 2
CHECK: Corresponding plug-in card installation, output configuration, output wiring
CHECK: Wiring is per EMC installation guidelines, input signal frequency, signal quality,
CHECK: Lower input signal frequency, reduce rate scaling
CHECK: Corresponding plug-in card installation, related controlling parameter selected
PRESS: Reset key (if unable to clear contact factory.)
CHECK: Wiring, connections, meter and host settings
input signal level, user input jumper, lower input signal frequency
scaling, update time, DIP switch setting
29
Analog Output Card Calibration
better (voltmeter for voltage output and/or current meter for current output) is
connected and ready. Then perform the following procedure:
1. Use the arrow keys to display
2.
3. Using the chart below, step through the five selections to be calibrated. At
4. When
Before starting, verify that a precision meter with an accuracy of 0.05% or
each prompt, use the PAXI arrow keys to adjust the output so that the
external meter display matches the selection being calibrated. When the
external reading matches, or if the range is not being calibrated, press PAR.
SELECTION
20. 0 - A
0. 0 - A
4. 0 - A
10. 0 u
0. 0 u
is displayed. Use the arrow keys to select
appears, press PAR twice and remove the external meters .
EXTERNAL METER
20.00
10.00
0.00
4.00
0.00
Adjust if necessary, press PAR
Adjust if necessary, press PAR
Adjust if necessary, press PAR
Adjust if necessary, press PAR
Adjust if necessary, press PAR
and press PAR.
ACTION
and press PAR.