M48T37Y-70MH1E STMicroelectronics, M48T37Y-70MH1E Datasheet - Page 12

• Manufacturer Part Number: M48T37Y-70MH1E
• Description: IC TIMEKPR NVRAM 256KBIT5V 44SOH
• Manufacturer: STMicroelectronics
• Series: Timekeeper®r
• Type: Clock/Calendar/NVSRAMr

Specifications of M48T37Y-70MH1E

• Memory Size: 256K (32K x 8)
• Time Format: HH:MM:SS (24 hr)
• Date Format: YY-MM-DD-dd
• Interface: Parallel
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 44-SOH
• Bus Type: Parallel
• User Ram: 32KB
• Operating Supply Voltage (typ): 5V
• Package Type: SOH
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Operating Temperature Classification: Commercial
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Pin Count: 44
• Mounting: Surface Mount
• Memory Configuration: 32K X 8
• Nvram Features: RTC
• Interface Type: Parallel
• Access Time: 70ns
• Supply Voltage Range: 4.5V To 5.5V
• Memory Case Style: SOIC
• No. Of Pins: 44
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-2854-5; M48T37Y-70MH1

M48T37Y, M48T37V
CLOCK OPERATIONS
Reading the Clock
Updates to the TIMEKEEPER
be halted before clock data is read to prevent
reading data in transition. The BiPORT™ TIME-
KEEPER cells in the RAM array are only data reg-
isters and not the actual clock counters, so
updating the registers can be halted without dis-
turbing the clock itself.
Updating is halted when a '1' is written to the
READ Bit, D6 in the Control Register 7FF8h. As
long as a '1' remains in that position, updating is
halted. After a halt is issued, the registers reflect
the count; that is, the day, date, and the time that
were current at the moment the halt command was
issued.
All of the TIMEKEEPER registers are updated si-
multaneously. A halt will not interrupt an update in
progress. Updating will resume within a second af-
ter the bit is reset to a '0.'
Setting the Clock
Bit D7 of the Control Register (7FF8h) is the
WRITE Bit. Setting the WRITE Bit to a '1,' like the
READ Bit, halts updates to the TIMEKEEPER reg-
isters. The user can then load them with the cor-
12/29
®
registers should
rect day, date, and time data in 24 hour BCD
format (see
WRITE Bit to a '0' then transfers the values of all
time registers (7FF1h, 7FF9h-7FFFh) to the actual
TIMEKEEPER counters and allows normal opera-
tion to resume. After the WRITE Bit is reset, the
next clock update will occur in approximately one
second.
Note: Upon power-up following a power failure,
both the WRITE Bit and the READ Bit will be reset
to '0.'
Stopping and Starting the Oscillator
The oscillator may be stopped at any time. If the
device is going to spend a significant amount of
time on the shelf, the oscillator can be turned off to
minimize current drain on the battery. The STOP
Bit is the MSB of the seconds register. Setting it to
a '1' stops the oscillator. When reset to a '0,' the
M48T37Y/V oscillator starts within one second.
Note: It is not necessary to set the WRITE Bit
when setting or resetting the FREQUENCY TEST
Bit (FT) or the STOP Bit (ST).
Table 5., page
13). Resetting the