KAD2710L-10Q68 Intersil, KAD2710L-10Q68 Datasheet - Page 15

• Manufacturer Part Number: KAD2710L-10Q68
• Description: IC ADC 10BIT 105MSPS SGL 68-QFN
• Manufacturer: Intersil
• Series: FemtoCharge™r

Specifications of KAD2710L-10Q68

• Number Of Bits: 10
• Sampling Rate (per Second): 105M
• Data Interface: Parallel
• Number Of Converters: 1
• Power Dissipation (max): 202mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 68-VQFN Exposed Pad, 68-HVQFN, 68-SQFN, 68-DHVQFN
• For Use With: KDC2710LEVAL - DAUGHTER CARD FOR KAD2710
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Layout Considerations
Split Ground and Power Planes
Data converters operating at high sampling frequencies
require extra care in PC board layout. If analog and digital
ground planes are separate, analog supply and ground
planes should be laid out under signal and clock inputs and
digital planes under outputs and logic pins. Grounds should
be joined under the chip.
Clock Input Considerations
Use matched transmission lines to the inputs for the analog
input and clock signals. Locate transformers, drivers and
terminations as close to the chip as possible.
Bypass and Filtering
Bulk capacitors should have low equivalent series
resistance. Tantalum is recommended. Keep ceramic
bypass capacitors very close to device pins. Longer traces
will increase inductance, resulting in diminished dynamic
performance and accuracy. Make sure that connections to
ground are direct, and low impedance.
LVDS Outputs
Output traces and connections must be designed for 50Ω
(100Ω differential) characteristic impedance. Keep trace
lengths equal, and minimize bends where possible. Avoid
crossing ground and power-plane breaks with signal traces.
Unused Inputs
The RST and 2SC inputs are internally pulled up, and can be
left open-circuit if not used.
CLKDIV is internally pulled low, which divides the input clock
by two.
VREFSEL is internally pulled up. It must be held low for
internal reference, but can be left open for external
reference.
Definitions
Analog Input Bandwidth is the analog input frequency at
which the spectral output power at the fundamental
frequency (as determined by FFT analysis) is reduced by
3dB from its full-scale low-frequency value. This is also
referred to as Full Power Bandwidth.
Aperture Delay or Sampling Delay is the time required
after the rise of the clock input for the sampling switch to
open, at which time the signal is held for conversion.
Aperture Jitter is the RMS variation in aperture delay for a
set of samples.
Clock Duty Cycle is the ratio of the time the clock wave is at
logic high to the total time of one clock period.
Differential Non-Linearity (DNL) is the deviation of any
code width from an ideal 1 LSB step.
15
KAD2710L
Effective Number of Bits (ENOB) is an alternate method of
specifying Signal to Noise-and-Distortion Ratio (SINAD). In
dB, it is calculated as: ENOB = (SINAD - 1.76)/6.02
Gain Error is the ratio of the difference between the voltages
that cause the lowest and highest code transitions to the
full-scale voltage (less 2 LSB). It is typically expressed in
percent.
Integral Non-Linearity (INL) is the deviation of each
individual code from a line drawn from negative full-scale
(1/2 LSB below the first code transition) through positive full-
scale (1/2 LSB above the last code transition). The deviation
of any given code from this line is measured from the center
of that code.
Least Significant Bit (LSB) is the bit that has the smallest
value or weight in a digital word. Its value in terms of input
voltage is V
Missing Codes are output codes that are skipped and will
never appear at the ADC output. These codes cannot be
reached with any input value.
Most Significant Bit (MSB) is the bit that has the largest
value or weight.
Pipeline Delay, or latency, is the number of clock cycles
between the initiation of a conversion and the appearance at
the output pins of the data.
Power Supply Rejection Ratio (PSRR) is the ratio of a
change in input voltage necessary to correct a change in
output code that results from a change in power supply
voltage.
Signal to Noise-and-Distortion (SINAD) is the ratio of the
RMS signal amplitude to the RMS sum of all other spectral
components below one half the clock frequency, including
harmonics but excluding DC.
Signal-to-Noise Ratio (SNR) (without Harmonics) is the
ratio of the RMS signal amplitude to the RMS sum of all
other spectral components below one-half the sampling
frequency, excluding harmonics and DC.
SNR and SINAD are either given in units of dBc when the
power level of the fundamental is used as the reference, or
dBFS (dB to full scale) when the converter’s full-scale input
power is used as the reference.
Spurious-Free-Dynamic Range (SFDR) is the ratio of the
RMS signal amplitude to the RMS value of the peak spurious
spectral component. The peak spurious spectral component
may or may not be a harmonic.
Two-Tone SFDR is the ratio of the RMS value of the lowest
power input tone to the RMS value of the peak spurious
component, which may or may not be an IMD product.
FS
/(2
N
-1) where N is the resolution in bits.
December 5, 2008
FN6818.0