ISL22313UFU10Z Intersil, ISL22313UFU10Z Datasheet
ISL22313UFU10Z
Specifications of ISL22313UFU10Z
Available stocks
Related parts for ISL22313UFU10Z
ISL22313UFU10Z Summary of contents
Page 1
... NUMBER PART (Notes 1, 2) MARKING ISL22313TFU10Z 313TZ ISL22313UFU10Z 313UZ ISL22313WFU10Z 313WZ NOTES: 1. Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2. Add “ ...
Page 2
Block Diagram SCL SDA A1 INTERFACE A0 Pin Descriptions MSOP PIN SYMBOL 1 SCL 2 SDA GND VCC 2 ISL22313 V CC POWER UP INTERFACE, 2 ...
Page 3
... ISL22313 Thermal Information Thermal Resistance (Typical, Note 3) 10 Lead MSOP +0.3 CC Maximum Junction Temperature (Plastic Package +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CC Recommended Operating Conditions Temperature Range (Full Industrial .-40°C to +125°C Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15mW 2.25V to 5. -2.25V to -5.5V Max Wiper Current ± ...
Page 4
Analog Specifications Over recommended operating conditions unless otherwise stated. Limits are established by characterization. (Continued) SYMBOL PARAMETER f -3dB cut off frequency cutoff (Note 16) RESISTOR MODE (Measurements between RW and RL with RH not connected, or between RW and ...
Page 5
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by characterization. (Continued) SYMBOL PARAMETER I V Current (standby Current (standby) V- Current (shutdown Current (standby) V-SB ...
Page 6
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by characterization. (Continued) SYMBOL PARAMETER SERIAL INTERFACE SPECS V A1, A0, SDA, and SCL input buffer IL LOW voltage V A1, A0, SDA, and SCL input buffer ...
Page 7
Operating Specifications Over the recommended operating conditions unless otherwise specified. Limits are established by characterization. (Continued) SYMBOL PARAMETER t A1 and A0 setup time SU and A0 hold time HD:A NOTES: 4. Typical values are for T = ...
Page 8
A0 and A1 Pin Timing START SCL SDA A0, A1 Typical Performance Curves 100 150 TAP POSITION (DECIMAL) FIGURE 1. WIPER RESISTANCE vs TAP POSITION [ I(RW ...
Page 9
Typical Performance Curves 2.0 1.6 1.2 0.8 50k V = 2.25V CC 0 TEMPERATURE (ºC) FIGURE 5. ZS ERROR vs TEMPERATURE 0 5.5V CC 0.25 0 -0. 2.25V CC -0. ...
Page 10
Typical Performance Curves 500 10k 400 300 200 100 116 TAP POSITION (DECIMAL) FIGURE 11. TC FOR RHEOSTAT MODE IN ppm SCL WIPER FIGURE 13. MIDSCALE GLITCH, CODE 7Fh TO 80h Pin Description Potentiometers Pins RH and ...
Page 11
Device Address (A1, A0) The address inputs are used to set the least significant 2 bits 2 of the 7-bit I C interface slave address. A match in the slave address serial data stream must match with the Address input ...
Page 12
FIGURE 15. DCP CONNECTION IN SHUTDOWN MODE The WIP bit (ACR[5 read-only bit. It indicates that non- volatile write operation is in progress impossible to write to the WR or ACR while WIP ...
Page 13
SCL FROM MASTER SDA OUTPUT FROM TRANSMITTER SDA OUTPUT FROM RECEIVER START FIGURE 17. ACKNOWLEDGE RESPONSE FROM RECEIVER SIGNALS FROM THE MASTER SIGNAL AT SDA SIGNALS FROM THE SLAVE S SIGNALS T FROM THE A IDENTIFICATION MASTER R BYTE WITH ...
Page 14
Data Byte. After reaching the memory location 0Fh, the pointer “rolls over” to 00h, and the device continues to output data for each ACK received.The master terminates the read operation issuing a NACK ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...