5T9306NLGI Integrated Device Technology (Idt), 5T9306NLGI Datasheet - Page 6

• Manufacturer Part Number: 5T9306NLGI
• Description: Clock Driver 2-IN LVDS 28-Pin VFQFPN EP Tray
• Manufacturer: Integrated Device Technology (Idt)

Specifications of 5T9306NLGI

• Package: 28VFQFPN EP
• Configuration: 1 x 2:1
• Input Signal Type: CML|eHSTL|HSTL|LVDS|LVEPECL|LVPECL|LVTTL
• Maximum Output Frequency: 1000 MHz
• Maximum Quiescent Current: 240 mA
• Operating Supply Voltage: 2.5 V

POWER SUPPLY CHARACTERISTICS FOR LVDS OUTPUTS
IDT5T9306 Data Sheet
AC DIFFERENTIAL INPUT SPECIFICATIONS
NOTES:
1. The output will not change state until the inputs have crossed and the minimum differential voltage range defined by V
2. V
3. V
NOTES:
1. These power consumption characteristics are for all the valid input interfaces and cover the worst case conditions.
2. The true input is held LOW and the complementary input is held HIGH.
IDT5T9306 REVISION B JANUARY 31, 2011
DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVDS
NOTES:
1. The 400mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V
2. A 1.2V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the V
3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.
4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.
Symbol
must be achieved to guarantee switching to a new state.
Symbol
Symbol
specification under actual use conditions.
actual use conditions.
DIF
CM
I
t
V
V
I
V
V
V
DDQ
R
V
TOT
I
D
V
PD
DIF
CM
DIF
THI
, t
IX
IN
specifies the minimum input voltage (V
X
H
specifies the maximum allowable range of (V
F
Quiescent V
Total Power V
Total Power Down Supply Current
Parameter
Input Signal Swing
Differential Input Signal Crossing Point
Duty Cycle
Input Timing Measurement Reference Level
Input Signal Edge Rate
Parameter
AC Differential Voltage
Differential Input Crosspoint Voltage
Common Mode Input Voltage Range
Input Voltage
Parameter
DD
DD
Power Supply Current
Supply Current
(1)
TR
(4)
- V
CP
TR
(2)
) required for switching where V
+ V
CP
) /2.
(2)
V
Outputs enabled
V
PD = LOW
(3)
DD
DD
(3)
= 2.7V., F
= Max., All Input Clocks = LOW
Test Conditions
REFERENCE CLOCK
TR
is the "true" input level and V
6
(1)
= 1GHz
(2)
CP
is the "complement" input level. The AC differential voltage
2.5V LVDS 1:6 CLOCK BUFFER TERABUFFER™ II
Min.
- 0.3
0.05
0.05
DIF
0.1
has been met or exceeded.
(1)
©2011 Integrated Device Technology, Inc.
Crossing Point
Typ.
Typ.
—
—
—
—
—
—
Value
400
1.2
50
2
+3.6
Max
Max
V
V
240
250
3.6
5
DD
DD
X
specification under
Units
V/ns
mV
%
V
V
Unit
Unit
mA
mA
mA
V
V
V
V
DIF
(AC)