KSZ8692PBI Micrel Inc, KSZ8692PBI Datasheet - Page 31

• Manufacturer Part Number: KSZ8692PBI
• Description: IC ARM9 PHY 10/100MBPS 400-PBGA
• Manufacturer: Micrel Inc

Specifications of KSZ8692PBI

• Applications: Networking & Communications
• Core Processor: ARM9
• Program Memory Type: External Program Memory
• Controller Series: KSZ
• Interface: EBI/EMI, Ethernet, I²C, I²S,PCI, SPI, UART/USART, USB
• Number Of I /o: 20
• Voltage - Supply: 1.235 V ~ 1.365 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 400-BGA
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Package Type: BGA
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ram Size: -
• Lead Free Status / RoHS Status: Supplier Unconfirmed, Lead free / RoHS Compliant
• Other names: 576-3627; KSZ8692PBI

Micrel, Inc.
March 2010
PCI Interface Signals
UART Signals
TAP Control Signals
Pin Number
P16
R16
R19
R20
P15
R15
R17
R18
N15
A18
A17
A16
A15
A14
T19
T20
C2
D5
A8
A1
MPCIACTN
CLKRUNN
Pin Name
U1DCDN
U1DSRN
U1CTSN
U1RXD
U2RXD
U3RXD
U4RXD
TRSTN
U1TXD
U2TXD
U3TXD
U4TXD
PBMS
PMEN
TMS
TDO
TCK
TDI
O (Tri-State)
O (Tri-State)
O (Tri-State)
O (Tri-State)
Pin Type
O (open
drain)
I/O
I/O
Ipd
Ipd
Ipd
Ipd
Ipd
Ipd
Ipd
O
I
I
I
I
I
PCI Power Management Enable (active low)
Pin Description
This is a CardBus only signal. The CLKRUNN signal is used by portable
CardBus devices to request the system to turn on the bus clock. Output is not
generated.
Mini-PCI active. This signal is asserted by the PCI device to indicate that its
current function requires full system performance. MPCIACTN is an open
drain output signal.
PCI Bridge Mode Select
Select the operating mode of the PCI Bridge.
When PBMS is High, the Host Bridge Mode is selected and on chip PCI bus
arbiter is enabled.
When PBMS is Low, the Guest Bridge Mode is selected and the on-chip
arbiter is disabled.
This pin is to inform the external PCI host that KSZ8692PB has detected a
wake-up event.
UART 1 Receive Data
UART 1Transmit Data
Must be enabled as output by software, otherwise tri-stated upon power-up.
External pull-up recommended.
UART 1Clear to Send
UART 1 Data Carrier Detect
UART 1 Data Set Ready
UART 2 Receive Data
UART 2 Transmit Data
Must be enabled as output by software, otherwise tri-stated upon power-up.
External pull-up recommended.
UART 3 Receive Data
UART 3 Transmit Data
Must be enabled as output by software, otherwise tri-stated upon power-up.
External pull-up recommended.
UART 4 Receive Data
UART 4 Transmit Data
Must be enabled as output by software, otherwise tri-stated upon power-up.
External pull-up recommended.
JTAG Test Clock
JTAG Test Mode Select
JTAG Test Data In
JTAG Test Data Out
JTAG Test Reset, asserted Low
31
M9999-031810-4.0
KSZ8692PB