CY7C63613-SC Cypress Semiconductor Corp, CY7C63613-SC Datasheet - Page 16

• Manufacturer Part Number: CY7C63613-SC
• Description: IC MCU 8K USB LS MCU 24-SOIC
• Manufacturer: Cypress Semiconductor Corp
• Series: M8™r

Specifications of CY7C63613-SC

• Applications: USB Microcontroller
• Core Processor: M8B
• Program Memory Type: OTP (8 kB)
• Controller Series: CY7C636xx
• Ram Size: 256 x 8
• Interface: PS2, USB
• Number Of I /o: 16
• Voltage - Supply: 4 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 428-1321

provides “HIGH” source current when the GPIO port is configured for CMOS outputs and the output data bit is written as a “1”.
Q2 and Q3 are sized to sink and source, respectively, roughly the same amount of current to support traditional CMOS outputs
with symmetric drive.
Port 3 has eight GPIO pins. Port 3 (8 bits) can be configured as inputs with internal pull-ups, open drain outputs, or traditional
CMOS outputs. An open drain output is also a high-impedance input. Port 3 offers high current drive with a typical current sink
capability of 12 mA. The internal pull-up resistors are typically 7 k .
NOTE: Special care should be exercised with any unused GPIO data bits. An unused GPIO data bit, either a pin on the chip or
a port bit that is not bonded on a particular package, must not be left floating when the device enters the suspend state. If a GPIO
data bit is left floating, the leakage current caused by the floating bit may violate the suspend current limitation specified by the
USB Specification. If a ‘1’ is written to the unused data bit and the port is configured with open drain outputs, the unused data bit
will be in an indeterminate state. Therefore, if an unused port bit is programmed in open-drain mode, it must be written with a ‘0.’
Notice that the CY7C63612/13 will always require that data bits P1[7:4], P2[7:0], P3[3:0] and DAC[7:0] be written with a ‘0.’
During reset, all of the GPIO pins are set to output “1” (input) with the internal pull-up enabled. In this state, a “1” will a lways be
read on that GPIO pin unless an external current sink drives the output to a “0” state. Writing a “0” to a GPIO pin enables the
output current sink to ground (LOW) and disables the internal pull-up for that pin.
9.1
During a reset, GPIO interrupts are disabled by clearing all of the GPIO interrupt enable ports. Writing a “1” to a GPIO Interrupt
Enable bit enables GPIO interrupts from the corresponding input pin.
DAC[7]
P0[7]
P1[7]
P2[7]
P3[7]
P0[7]
P1[7]
P2[7]
P3[7]
GPIO Interrupt Enable Ports
DAC[6]
P0[6]
P1[6]
P2[6]
P3[6]
P0[6]
P1[6]
P2[6]
P3[6]
Figure 9-10. Port 3 Interrupt Enable 0x07h (write only)
0.2 mA to 1.0 mA typical
Figure 9-7. Port 0 Interrupt Enable 0x04h (write only)
Figure 9-8. Port 1 Interrupt Enable 0x05h (write only)
Figure 9-9. Port 2 Interrupt Enable 0x06h (write only)
DAC[5]
P0[5]
P1[5]
P2[5]
P3[5]
P0[5]
P1[5]
P2[5]
P3[5]
Low current outputs
FOR
PRELIMINARY
Figure 9-6. DAC Port Data 0x30h (read/write)
Figure 9-2. Port 0 Data 0x00h (read/write)
Figure 9-3. Port 1 Data 0x01h (read/write)
Figure 9-4. Port 2 Data 0x02h (read/write)
Figure 9-5. Port 3 Data 0x03h (read/write)
DAC[4]
P0[4]
P1[4]
P2[4]
P3[4]
P0[4]
P1[4]
P2[4]
P3[4]
16
DAC[3]
P0[3]
P1[3]
P2[3]
P3[3]
P0[3]
P1[3]
P2[3]
P3[3]
DAC[2]
P0[2]
P1[2]
P2[2]
P3[2]
P0[2]
P1[2]
P2[2]
P3[2]
3.2 mA to 16 mA typical
DAC[1]
P0[1]
P1[1]
P2[1]
P3[1]
P0[1]
P1[1]
P2[1]
P3[1]
High current outputs
CY7C63612/13
DAC[0]
P0[0]
P1[0]
P2[0]
P3[0]
P0[0]
P1[0]
P2[0]
P3[0]