CY7C65113-SC Cypress Semiconductor Corp, CY7C65113-SC Datasheet - Page 6

• Manufacturer Part Number: CY7C65113-SC
• Description: IC MCU 8K USB HUB 4 PORT 28-SOIC
• Manufacturer: Cypress Semiconductor Corp

Specifications of CY7C65113-SC

• Applications: USB Hub/Microcontroller
• Core Processor: M8
• Program Memory Type: OTP (8 kB)
• Controller Series: USB Hub
• Ram Size: 256 x 8
• Interface: I²C, USB
• Number Of I /o: 11
• Voltage - Supply: 4 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SOIC (7.5mm Width)
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Package Type: SOIC
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: CY3649 - PROGRAMMER HI-LO USB M8428-1339 - KIT LOW SPEED PERSONALITY BOARD
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant
• Other names: 428-1331

CY7C65113C
2.0
Functional Overview
The CY7C65113C device is a one-time programmable 8-bit microcontroller with a built-in 12-Mbps USB hub that supports up to
four downstream ports. The microcontroller instruction set has been optimized specifically for USB operations, although the
microcontrollers can be used for a variety of non-USB embedded applications.
GPIO
The CY7C65113C has 11 GPIO pins (P0[7:0], P1[2:0]), both rated at 7 mA per pin (typical) sink current. Multiple GPIO pins can
be connected together to drive a single output for more drive current capacity.
Clock
The microcontroller uses an external 6-MHz crystal and an internal oscillator to provide a reference to an internal phase-locked
loop (PLL)-based clock generator. This technology allows the customer application to use an inexpensive 6-MHz fundamental
crystal that reduces the clock-related noise emissions (EMI). A PLL clock generator provides the 6-, 12-, and 48-MHz clock signals
for distribution within the microcontroller.
Memory
The CY7C65113C is offered with 8 KB of PROM.
Power-on Reset, Watchdog, and Free-running Timer
These parts include power-on reset logic, a Watchdog timer, and a 12-bit free-running timer. The POR logic detects when power
is applied to the device, resets the logic to a known state, and begins executing instructions at PROM address 0x0000. The
Watchdog timer is used to ensure the microcontroller recovers after a period of inactivity. The firmware may become inactive for
a variety of reasons, including errors in the code or a hardware failure such as waiting for an interrupt that never occurs.
2
I
C
2
The microcontroller can communicate with external electronics through the GPIO pins. An I
C-compatible interface accommo-
dates a 100-kHz serial link with an external device.
Timer
The free-running 12-bit timer clocked at 1 MHz provides two interrupt sources, 128-µs and 1.024-ms. The timer can be used to
measure the duration of an event under firmware control by reading the timer at the start of the event and after the event is
complete. The difference between the two readings indicates the duration of the event in microseconds. The upper four bits of
the timer are latched into an internal register when the firmware reads the lower eight bits. A read from the upper four bits actually
reads data from the internal register, instead of the timer. This feature eliminates the need for firmware to try to compensate if the
upper four bits increment immediately after the lower eight bits are read.
Interrupts
The microcontroller supports ten maskable interrupts in the vectored interrupt controller. Interrupt sources include the USB Bus
Reset interrupt, the 128-µs (bit 6) and 1.024-ms (bit 9) outputs from the free-running timer, five USB endpoints, the USB hub, the
2
GPIO ports, and the I
C-compatible master mode interface. The timer bits cause an interrupt (if enabled) when the bit toggles
from LOW ‘0’ to HIGH ‘1’. The USB endpoints interrupt after the USB host has written data to the endpoint FIFO or after the USB
controller sends a packet to the USB host. The GPIO ports also have a level of masking to select which GPIO inputs can cause
a GPIO interrupt. Input transition polarity can be programmed for each GPIO port as part of the port configuration. The interrupt
polarity can be rising edge (‘0’ to ‘1’) or falling edge (‘1’ to ‘0’).
USB
The CY7C65113C includes an integrated USB Serial Interface Engine (SIE) that supports the integrated peripherals and the hub
controller function. The hardware supports up to two USB device addresses with one device address for the hub (two endpoints)
and a device address for a compound device (three endpoints). The SIE allows the USB host to communicate with the hub and
functions integrated into the microcontroller. The CY7C65113C part includes a 1:4 hub repeater with one upstream port and four
downstream ports. The USB Hub allows power management control of the downstream ports by using GPIO pins assigned by
the user firmware. The user has the option of ganging the downstream ports together with a single pair of power management
pins, or providing power management for each port with four pairs of power management pins.
Document #: 38-08002 Rev. *D
Page 6 of 49