ADV611JST Analog Devices Inc, ADV611JST Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADV611JST
Manufacturer Part Number
ADV611JST
Description
IC CODEC DIGITAL CCTV 120LQFP
Manufacturer
Analog Devices Inc
Type
Video Codecr
Datasheet
1.ADV611JSTZ.pdf
(46 pages)
Specifications of ADV611JST
Rohs Status
RoHS non-compliant
Data Interface
Serial
Resolution (bits)
8 b
Sigma Delta
No
Voltage - Supply, Digital
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
120-LQFP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADV611JST
Manufacturer:
ad
Quantity:
1 831
Company:
Part Number:
ADV611JST
Manufacturer:
ADI
Quantity:
996
Company:
Part Number:
ADV611JSTZ
Manufacturer:
ADI
Quantity:
526
Company:
Part Number:
ADV611JSTZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
ADV611JSTZ
Manufacturer:
ADI
Quantity:
20 000
ADV611/ADV612
Host Interface Pins (Continued)
Name
ACK
FIFO_SRQ
STATS_R
LCODE
HIRQ
RESET
Power Supply Pins
Name
GND
VDD
Pins
1
1
1
1
1
1
Pins
16
13
O
O
I/O
O
O
O
I
I/O
I
I
Description
Host Acknowledge. The ADV611/ADV612 acknowledges completion of a Host
Interface access by asserting this pin. Most Host Interface accesses (other than the
compressed data register access) result in ACK being held high for at least one wait
cycle, but some exceptions to that rule are as follows:
• A full FIFO during decode operations causes the ADV611/ADV612 to de-assert
•
•
• An empty FIFO during encode operations causes the ADV611/ADV612 to de-
•
FIFO Service Request. This pin is an active high signal indicating that the FIFO
needs to be serviced by the host. (see FIFO Control register). The state of this pin
also appears in the Interrupt Mask/Status register. Use the interrupt mask to assert a
Host interrupt (HIRQ pin) based on the state of the FIFO_SRQ pin. This pin oper-
ates as follows:
• LO No FIFO Service Request condition (FIFOSRQ bit LO)
• HI FIFO needs service is nearly full (encode) or nearly empty (decode)
During encode, FIFO_SRQ is LO when the SWR bit is cleared (0) and goes HI
when the FIFO is nearly full (see FIFO Control register).
During decode, FIFO_SRQ is HI when the SWR bit is cleared (0), because FIFO
is empty, and goes LO when the FIFO is filled beyond the nearly empty condition
(see FIFO Control register).
Statistics Ready. This pin indicates the Wavelet Statistics (contents of Sum of
Squares, Sum of Value, MIN Value, MAX Value registers) have been updated and
are ready for the Bin Width calculator to read them from the host interface. The
frequency of this interrupt will be equal to the field rate. The state of this pin also
appears in the Interrupt Mask/Status register. Use the interrupt mask to assert a
Host interrupt (HIRQ pin) based on the state of the STATS_R pin. This pin oper-
ates as follows:
• LO No Statistics Ready condition (STATSR bit LO)
• HI Statistics Ready for BW calculator (STATSR bit HI)
Last Compressed Data (for field). This bit indicates the last compressed data word
for field will be retrieved from the FIFO on the next read from the host bus. The
frequency of this interrupt is similar to the field rate, but varies depending on
compression and host response. The state of this pin also appears in the Interrupt
Mask/Status register. Use the interrupt mask to assert a Host interrupt (HIRQ pin)
based on the state of the LCODE pin. This pin operates as follows:
• LO No Last Code condition (LCODE bit LO)
• HI Last data word for field has been read from FIFO (LCODE bit HI)
Host Interrupt Request. This pin indicates an interrupt request to the Host. The
Interrupt Mask/Status register can select conditions for this interrupt based on any
or all of the following: FIFOSTP, FIFOSRQ, FIFOERR, LCODE, STATR or
CCIR-656 unrecoverable error. Note that the polarity of the HIRQ pin can be
modified using the Mode Control register.
ADV611/ADV612 Chip Reset. Asserting this pin returns all registers to reset state.
Note that the ADV611/ADV612 must be reset at least once after power-up with this
active low signal input. For more information on reset, see the SWR bit description.
Description
Ground
+5 V dc Digital Power
(drive HI) the ACK pin, holding off further writes of compressed data until
the FIFO has one available location.
assert (drive HI) the ACK pin, holding off further reads until one location is filled.
–20–
REV. 0