KSZ8893MBL Micrel Inc, KSZ8893MBL Datasheet - Page 52

• Manufacturer Part Number: KSZ8893MBL
• Description: IC MANAGED SW 10/100 100-LFBGA
• Manufacturer: Micrel Inc

Specifications of KSZ8893MBL

• Controller Type: Ethernet Switch Controller
• Interface: MII, RMII, SNI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 100-LFBGA
• Number Of Primary Switch Ports: 3
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Power Supply Type: Analog/Digital
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Commercial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1603 - EVAL KIT EXPERIMENTAL KSZ8893MQL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-3090

The following is a sample procedure for programming the KSZ8893MQL/MBL using the SPI bus:
1. At the board level, connect the KSZ8893MQL/MBL pins as follows:
2. Enable SPI slave mode by setting the KSZ8893MQL/MBL strap-in pins PS[1:0] (pins 100 and 101,
3. Power up the board and assert reset to the KSZ8893MQL/MBL.
4. Configure the desired register settings in the KSZ8893MQL/MBL, using the SPI write or multiple write
5. Read back and verify the register settings in the KSZ8893MQL/MBL, using the SPI read or multiple read
6. Write a ‘1’ to the “Start Switch” bit to start the KSZ8893MQL/MBL with the programmed settings.
Note: The “Start Switch” bit cannot be set to ‘0’ to stop the switch after an ‘1’ is written to this bit. Thus, it is
recommended that all switch configuration settings are programmed before the “Start Switch” bit is set to ‘1’.
Some of the configuration settings, such as “Aging enable”, “Auto Negotiation Enable”, “Force Speed” and “Power
down” can be programmed after the switch has been started.
The following four figures illustrate the SPI data cycles for “Write”, “Read”, “Multiple Write” and “Multiple Read”.
The read data is registered out of SPIQ on the falling edge of SPIC, and the data input on SPID is registered on
the rising edge of SPIC.
December 2007
respectively) to “10”.
After reset, the “Start Switch” bit (register 1 bit [0]) is set to ‘0’.
command.
command.
KSZ8893MQL/MBL Pin #
99
97
98
96
SPIS_N
SPIQ
SPIC
SPID
X
0
0
WRITE COMMAND
0
Table 15. KSZ8893MQL/MBL SPI Connections
KSZ8893MQL/MBL Signal Name
SPIS_N
SCL
(SPIC)
SDA
(SPID)
SPIQ
0
0
Figure 8. SPI Write Data Cycle
0
1
0
A7 A6 A5 A4 A3 A2 A1 A0
52
WRITE ADDRESS
External Processor Signal Description
SPI Slave Select
SPI Clock
SPI Data
(Master output; Slave input)
SPI Data
(Master input; Slave output)
D7
D6
D5
WRITE DATA
D4
D3
M9999-121007-1.5
D2
D1
D0