TDA8026ET/C2,557 NXP Semiconductors, TDA8026ET/C2,557 Datasheet - Page 40

• Manufacturer Part Number: TDA8026ET/C2,557
• Description: IC SMART CARD SLOT 64TFBGA
• Manufacturer: NXP Semiconductors

Specifications of TDA8026ET/C2,557

• Controller Type: Smart Card Interface
• Interface: I²C
• Voltage - Supply: 2.7 V ~ 5.5 V
• Current - Supply: 210mA
• Operating Temperature: -25°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-TFBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NXP Semiconductors
11. Characteristics
TDA8026_1
Product data sheet
Table 42.
V
pins V
[1]
[2]
[3]
[4]
[5]
[6]
Table 43.
V
pins V
Symbol
V
V
V
V
I
I
t
Symbol
PORADJ Pin
I
I
I
DD
DD(INTF)
wake
L
IL
IH
DD
DD
DD
hys
DD(INTF)
th
f
Refer to
See
See
Typical value measurement based on a 85 % DC-to-DC converter and inductance efficiency; depends on
PCB layout and external component quality (inductor, capacitor).
Maximum measurement value based on a 125 mA I
inductance efficiency; depends on PCB layout and external component quality (inductor, capacitor).
= V
= V
clk(ext)
DD
DD
DD(INTF)
DD(INTF)
Figure 6 “The voltage supervisor circuit” on page
Section 8.3.2 “Description”
and V
and V
is the external clock frequency applied to pins CLKIN1 and CLKIN2.
Parameter
supply voltage
hysteresis
voltage
interface supply
voltage
threshold voltage decreasing voltage on pin V
supply current
interface supply
current
wake-up time
Supply
Supply supervisor
Section 8.6
UP
UP
= 3.3 V; f
= 3.3 V; f
Parameter
leakage current
LOW-level input current
HIGH-level input
current
All information provided in this document is subject to legal disclaimers.
= 10 F; T
= 10 F; T
for further information about DC-to-DC converter operation.
clk(ext)
clk(ext)
Rev. 1 — 9 March 2010
amb
amb
[1]
Conditions
on pin V
on pin V
V
on pin V
on pin V
on pin V
shutdown mode
Standby mode
clock-stop mode; All card slots in this
mode; f
CLKIN1 and CLKIN2
active mode; All V
f
I
I
shutdown mode
active mode; All V
f
increasing voltage on pin V
= 10 MHz; GND = 0 V; inductor = 10 H; decoupling capacitors on
clk(ext)
CC(1)
CC(3)
clk(ext)
CC(n)
= 25 C unless otherwise specified.
= 25 C unless otherwise specified.
= 10 MHz; GND = 0 V; inductor = 10 H; decoupling capacitors on
for a description of the voltage supervisor.
= I
= I
pins = 5 V
= 5 MHz;
= 5 MHz;
clk(ext)
DD
DD
DD
DD(INTF)
DD(INTF)
CC(2)
CC(4)
; DC-to-DC converter on
; DC-to-DC converter off;
Conditions
= 55 mA;
= I
= stopped on pins
CC(5)
CC(n)
CC(n)
CC
= 2 mA
11.
current load and a 75 % DC-to-DC converter and
pins = 5 V;
pins = 5 V;
Multiple smart card slot interface IC
DD
DD
Min Typ Max
[2]
[2]
[3]
[3]
[4]
[5]
[6]
[3]
1
1
1
Min Typ Max Unit
2.7
5.25 -
50
1.6
2.35 2.45 2.55 V
1.19 1.26 1.32 V
-
-
-
-
-
-
2.35 2.55 2.65 V
5.8
-
-
-
TDA8026
© NXP B.V. 2010. All rights reserved.
-
100 150 mV
-
25
300 450
3.7
210 260 mA
10
35
-
+1
+1
+1
5.5
5.5
3.6
40
-
15
-
11
40 of 59
Unit
V
V
V
mA
ms
A
A
A
A
A
A
A