ISP1181BDGG ST-Ericsson Inc, ISP1181BDGG Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/6/627/st-ericsson_inc_sml.jpg)
ISP1181BDGG
Manufacturer Part Number
ISP1181BDGG
Description
IC USB CNTRLR FULL-SPD 48-TSSOP
Manufacturer
ST-Ericsson Inc
Datasheet
1.ISP1181BBSUM.pdf
(71 pages)
Specifications of ISP1181BDGG
Controller Type
USB Peripheral Controller
Interface
Parallel
Voltage - Supply
3.3V, 5V
Current - Supply
26mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-1002-5
ISP1181BDGG,112
ISP1181BDGG,112
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1181BDGG
Manufacturer:
NXP
Quantity:
1 200
Company:
Part Number:
ISP1181BDGG
Manufacturer:
NXPLIPS
Quantity:
5 510
Part Number:
ISP1181BDGG
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
Table 31:
9397 750 13958
Product data
Bit
Symbol
Reset
Access
Endpoint Status Register: bit allocation
EPSTAL
R
7
0
12.2.3 Stall Endpoint/Unstall Endpoint
EPFULL1
Transaction — read 1 byte
Table 32:
These commands are used to stall or unstall an endpoint. The commands modify the
content of the Endpoint Status Register (see
A stalled control endpoint is automatically unstalled when it receives a SETUP token,
regardless of the packet content. If the endpoint should stay in its stalled state, the
microcontroller can restall it with the Stall Endpoint command.
When a stalled endpoint is unstalled (either by the Unstall Endpoint command or by
receiving a SETUP token), it is also reinitialized. This flushes the buffer: if it is an OUT
buffer it waits for a DATA 0 PID, if it is an IN buffer it writes a DATA 0 PID.
Code (Hex): 40 to 4F — stall (control OUT, control IN, endpoint 1 to 14)
Code (Hex): 80 to 8F — unstall (control OUT, control IN, endpoint 1 to 14)
Transaction — none
Bit
7
6
5
4
3
2
1
0
R
6
0
Endpoint Status Register: bit description
Symbol
EPSTAL
EPFULL1
EPFULL0
DATA_PID
OVERWRITE
SETUPT
CPUBUF
-
EPFULL0
R
5
0
Rev. 02 — 07 December 2004
DATA_PID
Description
This bit indicates whether the endpoint is stalled or not
(1 = stalled, 0 = not stalled).
Set to logic 1 by a Stall Endpoint command, cleared to logic 0 by
an Unstall Endpoint command. The endpoint is automatically
unstalled upon reception of a SETUP token.
A logic 1 indicates that the secondary endpoint buffer is full.
A logic 1 indicates that the primary endpoint buffer is full.
This bit indicates the data PID of the next packet (0 = DATA PID,
1 = DATA1 PID).
This bit is set by hardware, a logic 1 indicating that a new Setup
packet has overwritten the previous setup information, before it
was acknowledged or before the endpoint was stalled. This bit is
cleared by reading, if writing the setup data has finished.
Firmware must check this bit before sending an Acknowledge
Setup command or stalling the endpoint. Upon reading a logic 1
the firmware must stop ongoing setup actions and wait for a new
Setup packet.
A logic 1 indicates that the buffer contains a Setup packet.
This bit indicates which buffer is currently selected for CPU
access (0 = primary buffer, 1 = secondary buffer).
reserved
R
4
0
WRITE
OVER
R
3
0
Table
Full-speed USB peripheral controller
SETUPT
31).
R
2
0
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
CPUBUF
ISP1181B
R
1
0
reserved
R
0
0
34 of 70