ISP1181BDGG ST-Ericsson Inc, ISP1181BDGG Datasheet - Page 44
![no-image](/images/manufacturer_photos/0/6/627/st-ericsson_inc_sml.jpg)
ISP1181BDGG
Manufacturer Part Number
ISP1181BDGG
Description
IC USB CNTRLR FULL-SPD 48-TSSOP
Manufacturer
ST-Ericsson Inc
Datasheet
1.ISP1181BBSUM.pdf
(71 pages)
Specifications of ISP1181BDGG
Controller Type
USB Peripheral Controller
Interface
Parallel
Voltage - Supply
3.3V, 5V
Current - Supply
26mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-1002-5
ISP1181BDGG,112
ISP1181BDGG,112
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1181BDGG
Manufacturer:
NXP
Quantity:
1 200
Company:
Part Number:
ISP1181BDGG
Manufacturer:
NXPLIPS
Quantity:
5 510
Part Number:
ISP1181BDGG
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
14. Power supply
15. Crystal oscillator and LazyClock
9397 750 13958
Product data
Fig 9. ISP1181B with a 4.0 V to 5.5 V supply.
ISP1181B
V reg(3.3)
V CC(3.3)
V CC
V ref
The ISP1181B is powered from a single supply voltage, ranging from 4.0 V to 5.5 V.
An integrated voltage regulator provides a 3.3 V supply voltage for the internal logic
and the USB transceiver. This voltage is available at pin V
external pull-up resistor on USB connection D . See
The ISP1181B can also be operated from a 3.0 V to 3.6 V supply, as shown in
Figure
be connected to V
The ISP1181B has a crystal oscillator designed for a 6 MHz parallel-resonant crystal
(fundamental). A typical circuit is shown in
signal of 6 MHz can be applied to input XTAL1, while leaving output XTAL2 open.
The 6 MHz oscillator frequency is multiplied to 48 MHz by an internal PLL. This
frequency is used to generate a programmable clock output signal at pin CLKOUT,
ranging from 3 MHz to 48 MHz.
In ‘suspend’ state the normal CLKOUT signal is not available, because the crystal
oscillator and the PLL are switched off to save power. Instead, the CLKOUT signal
can be switched to the LazyClock frequency of 100 kHz
The oscillator operation and the CLKOUT frequency are controlled via the Hardware
Configuration Register, as shown in
004aaa140
•
•
•
Fig 11. Typical oscillator circuit.
CLKRUN switches the oscillator on and off
CLKDIV[3:0] is the division factor determining the normal CLKOUT frequency
NOLAZY controls the LazyClock signal output during ‘suspend’ state.
10. In this case, the internal voltage regulator is disabled and pin V
4.0 V to 5.5 V
Rev. 02 — 07 December 2004
CC
.
ISP1181B
Fig 10. ISP1181B with a 3.0 V to 3.6 V supply.
CLKOUT
XTAL2
XTAL1
Figure
6 MHz
Figure
12. The following bits are involved:
ISP1181B
18 pF
18 pF
Full-speed USB peripheral controller
V reg(3.3)
V CC(3.3)
V CC
11. Alternatively, an external clock
V ref
004aaa142
Figure
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
reg(3.3)
50 %.
9.
004aaa141
3.0 V to 3.6 V
ISP1181B
for connecting an
reg(3.3)
43 of 70
must