ISP1161A1BD ST-Ericsson Inc, ISP1161A1BD Datasheet - Page 134
![no-image](/images/manufacturer_photos/0/6/627/st-ericsson_inc_sml.jpg)
ISP1161A1BD
Manufacturer Part Number
ISP1161A1BD
Description
IC USB HOST/DEVICE CTRLR 64-LQFP
Manufacturer
ST-Ericsson Inc
Datasheet
1.ISP1161A1BMGA.pdf
(137 pages)
Specifications of ISP1161A1BD
Controller Type
USB 2.0 Controller
Interface
Parallel
Voltage - Supply
3.3V, 5V
Current - Supply
47mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-1162
ISP1161A1BD,157
ISP1161A1BD,157
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1161A1BD
Manufacturer:
PHILIPS
Quantity:
319
Part Number:
ISP1161A1BD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
ISP1161A1BDFA
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Company:
Part Number:
ISP1161A1BDTM
Manufacturer:
LATTICE
Quantity:
201
Company:
Part Number:
ISP1161A1BDTM
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Philips Semiconductors
9397 750 13961
Product data
24.4 Manual soldering
24.5 Package related soldering information
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 C or
265 C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in
most applications.
Fix the component by first soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time
must be limited to 10 seconds at up to 300 C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320 C.
Table 127: Suitability of surface mount IC packages for wave and reflow soldering
[1]
[2]
Package
BGA, HTSSON..T
SSOP..T
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
PLCC
LQFP, QFP, TQFP
SSOP, TSSOP, VSO, VSSOP
CWQCCN..L
•
•
For packages with leads on two sides and a pitch (e):
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45 angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
For more detailed information on the BGA packages refer to the (LF)BGA Application Note
(AN01026); order a copy from your Philips Semiconductors sales office.
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal
or external package cracks may occur due to vaporization of the moisture in them (the so called
popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated
Circuit Packages; Section: Packing Methods .
parallel to the transport direction of the printed-circuit board;
transport direction of the printed-circuit board.
[5]
, SO, SOJ
[3]
[1]
, TFBGA, USON, VFBGA
methods
[8]
, PMFP
Rev. 03 — 23 December 2004
[3]
, LBGA, LFBGA, SQFP,
[9]
, WQCCN..L
[8]
USB single-chip host and device controller
Soldering method
Wave
not suitable
not suitable
suitable
not recommended
not recommended
not suitable
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
[4]
[5][6]
[7]
ISP1161A1
Reflow
suitable
suitable
suitable
suitable
suitable
not suitable
133 of 136
[2]