ISP1161A1BD ST-Ericsson Inc, ISP1161A1BD Datasheet - Page 79
![no-image](/images/manufacturer_photos/0/6/627/st-ericsson_inc_sml.jpg)
ISP1161A1BD
Manufacturer Part Number
ISP1161A1BD
Description
IC USB HOST/DEVICE CTRLR 64-LQFP
Manufacturer
ST-Ericsson Inc
Datasheet
1.ISP1161A1BMGA.pdf
(137 pages)
Specifications of ISP1161A1BD
Controller Type
USB 2.0 Controller
Interface
Parallel
Voltage - Supply
3.3V, 5V
Current - Supply
47mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-1162
ISP1161A1BD,157
ISP1161A1BD,157
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1161A1BD
Manufacturer:
PHILIPS
Quantity:
319
Part Number:
ISP1161A1BD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
ISP1161A1BDFA
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Company:
Part Number:
ISP1161A1BDTM
Manufacturer:
LATTICE
Quantity:
201
Company:
Part Number:
ISP1161A1BDTM
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Philips Semiconductors
9397 750 13961
Product data
11.2.1 DMA for IN endpoint (internal DC to external USB host)
11.2.2 DMA for OUT endpoint (external USB host to internal DC)
11.2 Device DMA transfer
When the internal DMA handler is enabled and at least one buffer (Ping or Pong) is
free, the DREQ2 line is asserted. The external DMA controller then starts negotiating
for control of the bus. As soon as it has access, it asserts the DACK2 line and starts
writing data. The burst length is programmable. When the number of bytes equal to
the burst length has been written, the DREQ2 line is de-asserted. As a result, the
DMA controller de-asserts the DACK2 line and releases the bus. At that moment the
whole cycle restarts for the next burst.
When the buffer is full, the DREQ2 line will be de-asserted and the buffer is validated
(which means that it will be sent to the host when the next IN token comes in). When
the DMA transfer is terminated, the buffer is also validated (even if it is not full). A
DMA transfer is terminated when any of the following conditions are met:
When the internal DMA handler is enabled and at least one buffer is full, the DREQ2
line is asserted. The external DMA controller then starts negotiating for control of the
bus, and as soon as it has access, it asserts the DACK2 line and starts reading the
data. The burst length is programmable. When the number of bytes equal to the burst
length has been read, the DREQ2 line is de-asserted. As a result, the DMA controller
de-asserts the DACK2 line and releases the bus. At that moment the whole cycle
restarts for the next burst. When all data are read, the DREQ2 line will be de-asserted
and the buffer is cleared (which means that it can be overwritten when a new packet
comes in).
•
•
•
•
•
•
•
•
The SIE also checks for the device number and endpoint number and verifies
whether they are acceptable.
If the endpoint is enabled, the SIE checks the contents of the DcEndpointStatus
register. If the endpoint is empty, the data from USB is stored to FIFO during the
data phase, otherwise a NAK handshake is sent.
After the data phase, the SIE sends a handshake (ACK) to the host (except for ISO
endpoints).
The SIE updates the contents of the DcEndpointStatus register and the
DcInterrupt register, which in turn generates an interrupt to the microprocessor.
For ISO endpoints, the DcInterrupt register is updated as soon as data is received
because there is no handshake phase.
On receiving interrupt, the microprocessor reads the DcInterrupt register. It will
know which endpoint has generated the interrupt and reads the content of the
corresponding DcEndpointStatus register. If the buffer is full, it empties the buffer,
so that data can be received by the SIE at the next OUT token phase.
the DMA count is complete
bit DMAEN = 0
the DMA controller asserts EOT.
Rev. 03 — 23 December 2004
USB single-chip host and device controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
ISP1161A1
78 of 136